background image

9

A N T I - T I P B R A C K E T

I N S T A L L A T I O N

An anti-tip bracket and hardware is provided
with the Integrated unit. The anti-tip bracket
must be installed on a solid base.

If you are installing the unit in a space deeper
than 24", be sure to locate the anti-tip bracket
so that it engages the unit properly. It is impor-
tant that the anti-tip bracket is placed 24" from
the front of the unit without panels, to the the
back of the anti-tip bracket. Refer to illustra-
tions 1 and 2 below and note that for 27" (686)
wide units dimension A is 13

1

/

2

" (343), and 18"

(457) for 36" (914) wide units.

W O O D   F L O O R   A P P L I C A T I O N S

Use the six #12 x 2

1

/

2

" wood screws and the

six 

1

/

4

" flat washers provided. Drill pilot holes

3

/

16

" (5) diameter maximum, and be sure that

the screws penetrate through the flooring
material and into the wall plate a minimum of

3

/

4

" (19). Be sure that the screws hold tight.

Refer to illustration 1 below.

C O N C R E T E   F L O O R   A P P L I C A T I O N S

Use the two 

3

/

8

" x 3

3

/

4

" concrete wedge

anchors, two # 12 x 2

1

/

2

" wood screws and two

1

/

4

" flat washers provided. Be sure that the

anchors and screws hold tight. Refer to
illustration 2 below.

IMPORTANT NOTE: In some installations the
subflooring or finished floor may require
angling the wood screws used to fasten the
anti-tip bracket to the back wall. Refer to
illustrations 1 and 2.

I N T E G R AT E D  

I N S T A L L A T I O N   I N S T R U C T I O N S

To prevent the unit from tipping forward
and provide a stable installation, the unit
must be secured in place with the anti-tip
blocking bracket.

Make sure that there are no electrical
wires or plumbing in the area which the
screws could penetrate.

WOOD FLOOR 

Finished Flooring 

Underlayment 

Subflooring 

Wall Plate 

Finished Flooring 

Underlayment 

Subflooring 

Wall Plate 

CONCRETE 
FLOOR 

1

1

/

2

"

min 

(38)

Illus. 1

Illus. 2

S P E C I F I C A T I O N S

Dimension A

27" (686) Wide Units

13

1

/

2

" (343)

36" (914) Wide Units

18" (457)

Summary of Contents for 700BC





















Reviews: