Vista 5 M3 Digital Mixing System
Parameters 3-25
Document generated: 28.08.13
SW V4.9
Q
value
Rotary The Q (bandwidth) can be set to values from 0.27 through 8.7, in 30 steps.
For the HM and LM bands Q can be set only if ‘bell’ is selected.
HM, high-mid frequency, and LM, low-mid frequency: Q = 0.27 through 8.7,
in 30 steps.
High-Cut/Low-Cut Filter Parameters:
HI CUT/LO CUT x dB
Slope setting for the high- and low-cut filters, selectable from 12, 18, and
24 dB/octave (key toggles 12, 18, 24, 12...).
HI CUT/LO CUT
Rotary Cutoff frequency adjustment for the high- and low-cut filter: 20 Hz through
20 kHz, in 120 steps.
Notch Filter Parameters:
Please note that these two fields only appear if the notch filter is configured
(i.e., ‘EQ with Notch’ is selected for this channel in the console configura-
tion).
NOTCH On/Off
On/off function for the notch filter.
NOTCH
Rotary Center frequency for the notch filter: 20 Hz through 20 kHz, in 120 steps.
Notch Q
The notch filter’s Q is selectable from two fixed values; W (wide, Q=2), and
N (narrow, Q=10).
Note
The
EQ
,
HI CUT
and
LO CUT
hardware keys in the
CHANNEL PROCESSING
section can be used for activating or deactivating the complete EQ, high- and
low-cut filter sections, in addition to the
individual
on/off keys described
above.
5.1 Surround Channels
This view is the same as with mono or stereo channels. Please note that the
equalizer settings applied here will be valid for all surround signal legs
except
for the LFE
.
If an EQ setting has been made on a 5.1 surround channel, the normal Viston-
ics EQ display shows in small characters which signal legs are different from
the others (e.g. ‘Lf’), as shown left.
If one or more of the signal legs must be adjusted differently from others –
such as boosting HF in the center channel only, the
CHANNEL VIEW
has to be
selected. Then all the separate EQ settings for ‘Front’, ‘Center’, ‘LFE’ and
‘Rear’ are accessible.
3.4.1.2
Graphic EQ
Note
Since SW V4.7 there is the additional 30-band graphic EQ available; both
graphic and parametric EQs can be set up either for all or specific channels
using the Vista Configuration Editor.
If both EQs are configured within one single channel, the display is split into
two different touch areas, showing the combined response of both EQs. It
allows unfolding
either
the graphic
or
the parametric EQ parameters of this
channel on the Vistonics screen for adjustment. For details of the parametric
EQ please refer to the
previous chapter
.
Summary of Contents for Vista 5 M3
