Stryker Ultra Comfort SE 1703 Operation Manual Download Page 12

English

EN

1-4

1704-009-001 REV D

www.stryker.com

Introduction

This manual assists you with the operation or maintenance of your Stryker product. Read this manual before operating
or maintaining this product. Set methods and procedures to educate and train your staff on the safe operation or
maintenance of this product.

CAUTION

Improper usage of the product can cause injury to the patient or operator. Operate the product only as described in
this manual.

Do not modify the product or any components of the product. Modifying the product can cause unpredictable
operation resulting in injury to patient or operator. Modifying the product also voids its warranty.

Notes

This manual is a permanent part of the product and should remain with the product even if the product is sold.

Stryker continually seeks advancements in product design and quality. This manual contains the most current
product information available at the time of printing. There may be minor discrepancies between your product and
this manual. If you have any questions, contact Stryker Customer Service or Technical Support at 1-800-327-0770.

Product description

Ultra Comfort SE

™ is a non-powered support surface that assists in improving human patient outcomes by

redistributing pressure. This product is available in two different widths, 26” or 30”. The dimensions are intended to
match the stretcher litter deck.

Ultra Comfort SE

utilizes foam to redistribute pressure and to help with immersion.

Indications for use

This support surface is for use with human patients with existing or at risk of incurring pressure injuries. The safe
working load for

Ultra Comfort SE

is 700 lb (317 kg).

Ultra Comfort SE

assists in the prevention and treatment of all pressure injury stages (including stages 1, 2, 3, 4,

Unstageable and Deep Tissue Pressure Injury or all pressure injuries) and is recommended to be implemented in
combination with clinical evaluation of risk factors and skin assessments made by a healthcare professional.

Ultra Comfort SE

is intended to match the stretcher litter deck. This support surface is intended to be used for short-

term stays (treatment and recovery). Additionally, this product is not intended to be used within a home healthcare
setting.

Ultra Comfort SE

shall be used with a support surface cover at all times. The support surface cover can interact with all

external skin.

Operators of this support surface include healthcare professionals (such as nurses, nurse aids, or doctors).

This support surface is for use by patients in an acute care setting. This may include emergency department, Pre-
operative, Transport, Endoscopy, GI, critical care, step down, progressive care, med/surg, sub-acute care, and post
anesthesia care unit (PACU), operating room, or other locations as prescribed. This product is not intended to be sterile,
include a measuring function, or be used in a home healthcare environment.

Expected life

The

Ultra Comfort SE

has a 1 year expected life under normal use, conditions, and with appropriate periodic

maintenance.

Summary of Contents for Ultra Comfort SE 1703









































Reviews: