Stryker LIFEPAK 20 Inspection Procedure Download Page 46 | Manualshive

Page: 46 / 61

background image

LIFEPAK

®

20

Performance Inspection Procedure (PIP)

3201896-000_B

©2019 Stryker

--- CONTENTS ---

Page 46 of 61

PIP- Protective Earth Resistance Test

To perform the Protective Earth Resistance Test in accordance with IEC 62353:

1. Ensure the Safety Analyzer set to the IEC 62353

standard.

Note:

Consult your safety analyzer user manual to

perform a “Lead Zeroing” operation to eliminate
test lead resistance from your measurements.

2. Set the Safety Analyzer controls to measure Ohms

by selecting the Ohm button on the Safety
Analyzer.

3. Establish the setup as shown in Figure 1.30a.

Note:

Ensure all connectors and connection points

are clean and are firmly attached. If not, you will
see higher readings from the safety analyzer.

4. Measure the resistance of AC power cord

ground

conductor

per figure 1.30a. Record the resistance

value on the PIP checklist. The measured value
must be below 0.1 ohms.

(2)

(1)

Figure 1.30a

«
...
44
45
46
47
48
...
»

Summary of Contents for LIFEPAK 20






























































Reviews:

No comments

Related manuals for LIFEPAK 20

ImageQuant LAS 4000

Brand: GE Pages: 86

Brand: GE Pages: 160

Brand: GE Pages: 134

DISHSTAR ADA-SEER

Brand: Jackson Pages: 2

Brand: Macht Dental Pages: 8

MIAMI J ADVANCED

Brand: Össur Pages: 35

Brand: Össur Pages: 38

Brand: Össur Pages: 8

Brand: Össur Pages: 72

Brand: Össur Pages: 76

Miami Lumbar Posteo

Brand: Össur Pages: 45

Brand: Össur Pages: 29

Icelock Clutch 211

Brand: Össur Pages: 26

i-limb hand Series

Brand: Össur Pages: 27

i-Digits Quantum

Brand: Össur Pages: 231

Brand: Guyatone Pages: 2

Brand: ebm-papst Pages: 10

CEAG Exit Cube 33822 LED CGLine+

Brand: Eaton Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands