manualshive.com logo in svg

Stryker LIFEPAK 20, Inspection Procedure

Share
Download
Stryker LIFEPAK 20 Inspection Procedure Download Page 22

LIFEPAK

®

20 

Performance Inspection Procedure (PIP)

 

 

 

 

3201896-000_B

    

©2019 Stryker                                                                         

       --- CONTENTS ---   

 

 

Page 22 of 61

 

 

 

 

PIP - 5-Lead ECG Tests 

Note:

 Perform this test if 5-lead ECG cable is used. Otherwise, skip to the next test. 

The 5-Lead ECG  tests consist of:  

                     

PIP - 5-Lead ECG Leads Off Detection Test

 

                     

PIP - 5-Lead ECG Gain Test 

 

PIP - 5-Lead ECG Leads Off Detection Test 

 

1.

  Connect the 5-wire ECG cable between the device and Impulse 7000DP as 

shown in Figure 1.12. 

2.

  Set the Impulse 7000DP output to a 1-mv, 10-Hz sine wave. 

3.

  Set the device 

Lead

 selection to 

LEAD II

. 

4.

  Remove the RL lead from the Impulse 7000DP, and verify the device displays 

an 

ECG LEADS OFF

 message and a repeating priority 3 tones shall sound 

when the Lead is removed. Reconnect the RL lead. 

5.

  Remove the RA lead from the Impulse 7000DP, and verify the device displays 

an 

RA LEADS OFF

 message and a repeating priority 3 tones shall sound when 

the Lead is removed. Reconnect the RA lead. 

6.

  Remove the LL lead from the Impulse 7000DP, and verify the device displays 

an 

LL LEADS OFF

 message and a repeating priority 3 tones shall sound when 

the Lead is removed. Reconnect the LL lead. 

7.

  Set the device lead selection to 

LEAD I

. 

8.

  Remove the LA lead from the Impulse 7000DP. 

9.

  Verify the device displays an 

LA LEADS OFF

 message and a repeating priority 

3 tones shall sound when the Lead is removed. Reconnect the LA lead. 

10.

 Set the device 

LEAD 

selection to 

C LEAD

. 

11.

 Remove the C1/V1 Lead from the Impulse 7000DP. 

12.

 Verify the device displays a 

C LEADS OFF

 message and a repeating priority 3 

tones shall sound when the Lead is removed. Reconnect the C1/V1 lead. 

13.

 Continue to the next test with this setup in place. 

 

Figure 1.12: 5 Lead  ECG Leads Test 

Setup

 

Summary of Contents for LIFEPAK 20






























































Reviews:

No comments

Brands by name

Popular brands

Load more brands