Stryker LIFEPAK 20 Inspection Procedure Download Page 15

Page: 15 / 61

LIFEPAK

Performance Inspection Procedure (PIP)

3201896-000_B

--- CONTENTS ---

Page 15 of 61

PIP - Keypad Verification Tests

To perform Keypad Verification Tests:

1. Select

TESTS

in the Service menu.

2. Select

BUTTONS

in the

Service/Tests

submenu as shown in Figure 1.6.

3. Press each front panel button when prompted by the flashing button

legend (although you may press the buttons in any order).

4. Verify with each button pressed that its associated text box is highlighted.

Note:

A failure is indicated by a text box that is not highlighted. It is

normal for the buttons with up/down arrows to highlight only the
arrows.

5. Press the switch located between the

OPTIONS

and

PAUSE

buttons.

Note:

The switch is hidden in the elastomer keypad.

6. Verify the

TEST COMPLETE

message appears on the bottom of the

screen and the

Service LED

is not on.

7. Press the

SPEED DIAL

to exit at the end of the test.

8. Continue with the next test while still in Service mode.

Figure 1.6: Keypad Test

Summary of Contents for LIFEPAK 20






























































Search results

Summary of Contents for LIFEPAK 20

Reviews:

Brands by name

Popular brands

Stryker LIFEPAK 20, Inspection Procedure

Search results

Summary of Contents for LIFEPAK 20

Reviews:

Brands by name

Popular brands