manualshive.com logo in svg

Stryker LIFEPAK 20, Inspection Procedure

Share
Download
Stryker LIFEPAK 20 Inspection Procedure Download Page 11

LIFEPAK

®

20 

Performance Inspection Procedure (PIP)

 

 

 

 

3201896-000_B

    

©2019 Stryker                                                                         

       --- CONTENTS ---   

 

 

Page 11 of 61

 

 

 

 

PIP - Manual Mode Access

 

It is recommended that the device be set up for Manual mode when performing the PIP. 

 

Note:

 If you do not wish to change the setup for a device configured with manual access restrictions, it may be necessary to use the 

reserved technician passcode of 5433 to gain access to Manual mode. 

Note:

 Be sure to make note of the customer settings to restore the device to the user-selected 

MANUAL ACCESS

 

configuration at the completion of this PIP.

 

 

 

 

To perform the device for Manual mode access: 
1.  Access the Setup mode as follows: 

a. Press and hold 

OPTIONS

 and 

EVENT

, and then turn the device 

ON

. 

b. When the Setup mode passcode prompt appears enter 5433. 

2.  Select 

MANUAL MODE

 in the Setup menu. 

3.  In the Setup/Manual Mode submenu, set the Manual Access selection to 

Manual/Direct

 as shown in Figure 1.2. 

4.  Turn the device 

OFF

 by pressing 

ON

 for two seconds. 

 

Figure 1.2: Manual Mode Access 
 

Summary of Contents for LIFEPAK 20






























































Reviews:

No comments

Brands by name

Popular brands

Load more brands