manualshive.com logo in svg

Stryker 6086, Operation & Maintenance Manual

Share
Download
Stryker 6086 Operation & Maintenance Manual Download Page 19

www.stryker.com

6086-009-001 REV B

19

Return To Table of Contents

Vehicle Safety Hook Selection

Note: 

The Vehicle Safety Hook Selection and Installation instructions on 

page 19

 through 

page 22 

are intended for 

cots that you will NOT use with Power-LOAD.  For Model 6086 cots with the Power-LOAD option, see the Power-LOAD 
Operations/Maintenance Manual for installation instructions.  Power-LOAD ships and is installed with its own safety 
hook, thus no additional hook is needed.

The vehicle safety hook is a device that ships with the cot. The cot safety bar and vehicle safety hook are designed 
to keep the cot from being accidentally removed from the vehicle and to provide increased operator assurance and 
confidence when loading and unloading. The safety hook was designed for compatibility and proper operation when 
loading and unloading the cot from a vehicle that is compliant with Federal Regulation KKK-A-1822. 

Stryker offers three different types of safety hooks 
that are ordered and shipped with your cot.  These 
safety hook types are designed to meet the needs of 
various emergency vehicle configurations, specifically 
the length and location of the floor structure support 
that is located in the rear of the vehicle.  

Consider the following information when selecting 
which safety hook is appropriate for your vehicle 
configuration:

• 

Determine the location of the floor structure 
support where there is adequate room to mount 
the safety hook.

• 

Ensure that the safety hook can be securely 
mounted into the back of the vehicle while 
providing adequate bumper clearance to allow the 
cot to be loaded and unloaded from the vehicle.

• 

Note the differences in vehicle design.  Each safety 
hook provides a different mounting location option 
to maintain the appropriate distance between the 
face of the safety hook and the edge of the door sill.

Due to the differences in vehicle dimensions and the floor structure support locations, each safety hook requires a 
different mounting location.  See “Vehicle Safety Hook Installation” to determine the correct positioning for safety hook 
installation.

Note:  

When replacing an existing safety hook with a new style, adjust the mounting location to maintain the proper 

position of the safety hook face.

Long Safety Hook

6060-036-018

J-Style Safety Hook

6092-036-018

Short Safety Hook

6060-036-017

Figure 6:  Safety Hook Types

Summary of Contents for 6086































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands