background image

20 

JOHNSON® CONTROL -  MR3CCUHV 

Manual
Defrost
Button

Enter
Button

Fan

Status

LED

Defrost

Status

LED

Compressor

Status

LED

Up
Button

Down
Button

To Lock and Unlock The Unit for Programming 

Press the Enter, Up, and 
Down buttons in sequence 
and hold them all down until 
“- - -” is displayed. Hold for 
about 10 seconds until the 
current temperature is dis-
played. This toggles the key-
pad between locked and 
unlocked. 

 

To change the set point 

1.  Hold the Enter button 

down for 3 seconds. 
The display will change 
to show the set point. 
Release the Enter     
button. 

2.  Press the Up or Down 

button until you reach 
the new set point. 

3.  Press the Enter button 

to save the new set-
point. 

 

Note: 

If the Enter button is not pressed after select-

ing the new set point, the new set point is not saved, 
and the control will revert to the original set point. 

 

To Begin a Manual Defrost Cycle 

 

Hold the Defrost button 
down for 3 seconds. 

 

 

To Begin a Deep Freeze Cycle 

 

Press the Enter and Up but-
tons in sequence and hold 
both for 5 seconds. The 
compressor status LED will 
light. 

To Program Values Other Than The Setpoint 

A parameter settings reference page is included in Table 3 
of this bulletin. Filling out the parameter settings before    
programming may be helpful. 

 

1. 

H

old the Enter button down 

for about 10 seconds. The 
display will change to HY. 

2.  Press the Up or Down  button 

until the desired parameter is 
displayed. 

3.  Press the Enter button. The 

parameter’s current value is 
displayed. 

4.  Press the Up or Down  button 

until the desired value is 
shown. 

5.  Press the Enter button to 

save the new value. After 
10 seconds of inactivity, the 
display will return to its       
normal function. 

 

Note: If the Enter button is not pressed after selecting the 
new value, the new value is not saved, and the control will 
revert to using the previous value. 

 

To Run the Self-Test Procedure 

 

Press the Up and Down buttons 
in sequence, and hold for 5     
seconds. 

 

 

IMPORTANT: 

Disconnect loads before beginning        

Self-test procedure. Cycle power to resume normal           
operation.

 

Summary of Contents for Oasis CO2739R






















Reviews: