Strong SRT 7500 User Manual Download Page 10

Page: 10 / 20

PART 2 • English

English

symbol next the channel name. After you have marked all channels for locking, your changes will be saved by pressing
bACK. Now you will have to enter your PIN every time you are switching to a locked channel. If you are not entering the
PIN, the receiver will show after a few seconds the picture of the last watched channel until you enter the correct PIN.
For more information, please refer to

“Parental Settings”

in chapter 5.4 CONFIGURATION.

note

Above described actions for Move and Delete can only be applied for

“All Channels”

list mode. If you

are in a different channel list mode, a message will be shown to change to this mode or not.

5.2 favourites

In MAIN MENU screen, use the

buttons to select Favourites and press oK to enter this menu. In this menu, you

can add channels to the favourite list. With bACK you can always cancel actions and exit the actual menu or submenu.
Select desired channels you want to add to the list. Use the

buttons to go through the channel list, furthermore

you can use the RED (PG up) and GREEn (PG down) button to scroll page wise. With oK you switch to the selected
channel. The frequency and the satellite name of the selected channel will be displayed below its picture. With oK you
can mark and unmark channel to FAV group, your changes will be saved as soon you press bACK.

5.3 Installation

In MAIN MENU screen, use the

buttons to select Installation and press oK to enter this menu. The Installation

Menu consists of following sub-menus: Antenna Installation, First Time Installation, Automatic Search, Manual Search,
Load Settings and Save Settings.

5.3.1 Antenna Installation

In submenu Installation, use the

buttons to select Antenna Installation and press oK to enter this menu. Here you

can access all important settings concerning your dish installation and you will be able to see signal level (strength)/
signal quality (signal to noise ratio) for selected satellite and transponder. With bACK you can always cancel actions and
exit the actual menu or submenu.

Satellite:

Currently approx. 50 preset satellites exist, such as Astra, Hotbird, EuroBird, Turksat etc.
and 4 user defined satellites as User1 - User4. Use the

button and

buttons to

select the satellite which is in your area of reception from the list. By pressing oK at the
selected satellite, you can enter a new name for it. Therefore you can use the nUMERIC
buttons.

Dish Type:

Use the

buttons to change the used dish type. You can choose between DiSEqC 1.0,

DiSEqC 1.2 and GOTO X. If you have chosen the DiSEqC 1.2 or GOTO X you can enter the
according setup menu with oK.

DiSEqC 1.0:

Use this setup if you are using dish installation with one or multiple fixed dishes. The
default setup for your country specific satellite is already done (AUT-Astra19.2, GER-
Astra19.2, CZE-Astra23.5, SLO-Astra23.5) on DiSEqC input 1. If your installation contains
another satellite or satellites, please setup corresponding SAT on DiSEqC input 2, 3 and 4.

5.3.1.1 DiSEqC 1.2 Setup Menu

Use this setup if you are using dish installation with motorized antenna. After confirming DiSEqC 1.2 setting with oK
in Dish Type, you will enter the DiSEqC 1.2 Setup Menu. With bACK you can always cancel actions and exit the actual
menu or submenu.

Transponder Settings:

If you have chosen a satellite from the installed SAT table, the corresponding reference
transponder is already set. If you want to change the values for reference TP, press oK to
enter its submenu. Use the nUMERIC buttons to enter new values and use

buttons

to navigate. Your changes will be saved as soon you press bACK.

Go to Angle:

Use the

buttons to navigate and nUMERIC buttons to enter a value for the angle you

want to go to. Some DiSEqC 1.2 positioners do not support the

“go to angle”

command. If

your positioner does not support this function, you can enter 000 for the angle in order to
turn the positioner to the reference zero position.

Motor Speed:

Use the

buttons to change the speed between fast and slow.

Drive Motor:

Use the

buttons to drive motor to west or east. To drive the motor towards a specific

direction,

buttons should be kept pressed.

Enable/Disable Limits:

Use the

buttons to enable or disable the software limits for defined east or west limits.

Store Position:

If your adjustment has reached the maximum signal strength and quality for the desired
position, you can press oK in order to save this setting.

Set East Limit:

If you press oK at the position your motor is currently moved to, it will be saved as east
limit. Now your motor will not move to the east over this set limit.

Set West Limit:

If you press oK at the position your motor is currently moved to, it will be saved as west
limit. Now your motor will not move to the west over this set limit.

Recalculate Positions:

Use this function to restore possible misaligned dish position. Setup one of the satellite