Strong SM-RAZOR-T-L Installation Manual Download Page 11 | Manualshive

Page: 11 / 12

background image

© 2013 Strong

TM

pg.11

SM-RAZOR-T Installation Manual

Lifetime Limited Warranty

Strong™ Mounts have a Lifetime Limited Warranty. This warranty
includes parts and labor repairs on all components found to be
defective in material or workmanship under normal conditions of use.
This warranty shall not apply to products which have been abused,
modified or disassembled. Products to be repaired under this warranty
must be returned to Snap AV or a designated service center with prior
notification and an assigned return authorization number (RA).

Lifetime

Contacting Technical Support

Phone: (866) 838-5052

Email: [email protected]

«
...
9
10
11
12
»

Summary of Contents for SM-RAZOR-T-L













Reviews:

No comments

Related manuals for SM-RAZOR-T-L

Viera TX-32LED7FM

Brand: Panasonic Pages: 44

Brand: Amtran Pages: 31

Network_Extender_Business

Brand: Verizon Wireless Pages: 42

FT2A-CBLR-BRKT-1200

Brand: Crestron Pages: 2

Brand: TCL Pages: 54

Brand: TCL Pages: 23

Brand: Cello Pages: 44

Brand: Anchor Pages: 2

Brand: Echogear Pages: 2

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 24

Brand: Panasonic Pages: 28

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 26

Brand: Panasonic Pages: 28

Brand: Panasonic Pages: 40

Brand: Panasonic Pages: 32

Brand: Panasonic Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands