2
1.
DO NOT
use this product for any purpose other than cutting ice fishing holes. Ice augers are precision cutting tools
built for the ice fisherman, and must be properly maintained and handled with caution during both cutting and
transporting. When not in use, always store with blade guard attached.
2.
DO NOT
use attachments other than those available from the manufacturer.
3.
DO NOT
alter this product in any manner; doing so is dangerous and
voids all warranties
.
4.
DO NOT
allow children or adults weighing under 100 lbs. to operate this equipment.
5.
DO NOT
operate under the influence of drugs or alcohol.
6.
DO NOT
allow your body, loose clothing, drawstrings, scarves, hats or other materials to come in contact with the
Powerhead, Starter Assembly or Auger (Drill) unit at any time.
7.
DO NOT
operate if, upon pulling the starter rope or after drilling holes, the auger (drill) unit rotates or if the rope pulls
hard.
DO NOT OPERATE
. Have the unit checked by a qualified mechanic.
8.
DO NOT
allow the engine to run or operate while moving or transporting to another location.
9.
DO NOT
continue to use this product in the event of mechanical or electrical failure.
10.
This product produces considerable cutting force that is felt by the operator. Make sure your feet are firmly planted and
that the handles are held firmly while operating this product.
11.
Always check the operation of the throttle system to ensure the carburetor control is completely returning
to the idle position when the throttle lever is released.
12.
Check cutting blades and auger shaft screws before and after each use to make sure they are tight.
13.
During operation, the auger unit could possibly stop. Be prepared at all times to release the throttle lever.
14.
Everyone who uses this product should read this manual before operating this unit.
15.
The cutting blades on the ice auger are razor sharp. Use extreme care when handling.
16.
The manufacturer recommends that all augers, Lazer Mag Xpress, Strike-Lite, Lazer 224, Mag 2000, Magnum, Lazer Mag, Lazer Pro
and Electra Lazer 12000 DP be used for ice cutting only.
Carefully remove blade guard and make sure blade bolts are tight.
8mm bolts and 8mm closed
end wrench
2
Remove Metric Allen wrench and unscrew the collar bolt from auger.
The large and small
holes from each
component must line
up before installing
the collar bolt
3
Remove Black plastic cap from drive shaft. Insert auger into drive shaft and install collar bolt.
Collar bolt inserts into the large hole, passes through the
drive shaft and threads into the small hole of the metal
collar. Make sure bolt is tight. Some wiggle is normal
between the power head and auger. Check and tighten
often.
Push down and twist
to line up holes
Large Holes
Metal Collar
Allen Wrench
Collar Bolt
Plastic Collar
Black Cap
Drive Shaft
LAZER BLADE
1
Operation
1.
Start engine as explained in this manual.(See page 4-7). For best cutting performance, run
engine at idle for one minute before drilling.
2.
Hold the unit in a vertical position with your
right hand
pushing downward to
open throttle
, and your
left hand
firmly
holding the
opposite handle
.
3.
This product produces considerable cutting force that is felt by the operator. Make sure your feet are firmly planted and
that the handles are held firmly while operating this product, centrifugal clutch will engage and the auger will begin to
rotate.
4.
During the operation of cutting, the auger could possibly stop if it comes in contact with a foreign object or if it binds in the
hole. Be prepared at all times to release the throttle lever to avoid rotation of the handle assembly.
Assembly
4.
After assembly is complete, you can conveniently store your allen
wrench on the underside of the throttle pedal.
5.
It is recommended that the collar bolt be checked and torqued
firmly before and after every use.
Allen Wrench Storage
t
!
t
!
t
!
t
!
t
!
t
!
t
!
t
!
t
!
t
!
t
!
t
!
t
!
t
!
t
!
t
!
t
!
t
!
It is recommended that everyone who uses this product should read the StrikeMaster OPERATING
MANUAL and view the videos at http://www.strikemaster.com/video.html before operating
IMPORTANT SAFEGUARDS