HYDRO-PRO 150® WATER SAVER NOZZLE
INSTRUCTIONS FOR SERVICING SPRAY NOZZLE
If the Hydro-Pro 150 begins to leak from the seat (14) or rear of the body (1) follow
the steps below. For best results, order original Strahman parts.
1. Disassemble the renewable cover (2) by loosening and removing the six cover screws (4) (not shown).
2. Lift the body (1) free of the cover (2). Remove the ratchet assembly hinge (3), ratchet (5), and ratchet spring pin (13).
Place the body in boiling water for 2-3 minutes to release the Loc-Tite bond on stem screw (11). Remove the stem
screw (11) and swivel the U-bracket (17) down or up away from the stem (9).
3. Remove the snap rings (7) from the font and rear of the water saver body (1). Push on the rear of the stem (9) until
the seat stem (14) and stem spring (10) are free of the body.
4. Carefully press the housing (8) out of the rear of the water saver body (1). Precautions should be taken to avoid
damaging the inside of the water saver body.
5. lnstall a new “O-ring” (6) on the seat (14). Install a new “O-ring” (6) on the new housing (8).
6. lnstall seat (14) and snap-ring (7) in the front of the water saver body (1). Install the stem (9) and then stem spring
(10) from the rear of the water saver body.
7. Install the housing (8) in the rear of the body and compress the stem spring (10). Install a snap ring (7) in the rear of
the water saver body.
8. Swivel the U-bracket (17) back into place over the end of the stem (9). Apply Loc-Tite 271 to the stem screw (12) and
reinstall.
9. Re-install the body (1) and ratchet assembly-hinge (3) ratchet (5), and ratchet spring pin (13) in the new renewable
cover (2). Reinstall the six cover screws (4) (not shown).
PARTS LIST
ITEM
NO.
ORDER NUMBER
DESCRIPTION
1
HPBODYASSM
HYDRO-PRO 150® BODY
2
WSHP1COVER0007
RENEWABLE COVER - BLACK
WSHP1COVER0008
RENEWABLE COVER - RED
WSHP1COVER0009
RENEWABLE COVER - WHITE
3
HP1HINGESS
RATCHET HINGE ASSY, SST
4
HP1SCR
COVER SCREWS (SET OF 6) (NOT SHOWN)
5
HP150RACHETASSY
RATCHET
6
ORNG18MM02MMEA
O-RINGS (SET OF 6)
7
HP1SNAPRINGSS
SNAP RETAINING RING, SST
8
HP1HOUSASSY
HOUSING, SST
9
HP150STEMASSY
STEM ASSEMBLY
10
SPRG12339S3SS
SPRING STEM (SET OF 6), SST
11
MSN8320038LWOZ
STEM SCREW & WASHER (SET OF 6)
12
SPRG12410S5SS
RATCHET SPRING, SST
13
HP1SPINSS
RATCHET SPRING PIN (SET OF 6) SST
14
HP1SEAT
HP 150 SEAT, SST
HP1SEATLFSS
HP 150 LOW FLOW SEAT, SST
15
HPILARM9
LEVER ARM
16
WSHP1LPIV0000
LEVER ARM PIVOT ASSY
17
HP1UBRKSS
U-BRACKET, SST
3
5
11
10
1
2
15
12
13
6
14
7
17
9
6
7
8
2
16
3
5
11
10
1
2
15
12
13
6
14
7
17
9
6
7
8
2
16
3
5
11
10
1
2
15
12
13
6
14
7
17
9
6
7
8
2
16
3
5
11
10
1
2
15
12
13
6
14
7
17
9
6
7
8
2
16
Add pipe sealant at this connection;
tighten to ensure an adequate seal.
