background image

Care & Cleaning

V

ITREOUS

 

ENAMEL

Burner caps.

Cloth wrung out in hot soapy water. Stubborn stains can be

removed  with  a  cream  paste  approved  by  the  Vitreous

Enamel  Development  Council,  liquid  cleaner  or  by  rubbing

with fine steel wool soap pads.

A

LUMINIUM

 

Trim, Hotplate burner bodies.

It  is  advisable  to  clean  the  decorative  trims  regularly  to

prevent any build up of soiling which may detract from the

appearance  of  the  appliance.  The  recommended  method  of

cleaning is to wipe over the trims with a soft cloth wrung out

in warm water, or mild non-abrasive cleaner. (If in doubt try

the cleaner on a small area of trim which is not noticeable in

normal use), then after wiping with a cloth wrung out in clear

water, dry with a soft clean cloth.

Use a nylon brush to remove any cleaning materials, water or

dirt from the hotplate burner bodies. After cleaning, wipe dry

and refit to the hob ensuring they are correctly seated.

Check parts are reassembled correctly by lighting the burners

and allowing to dry out.

P

LASTIC

Control knobs.

Wipe with a cloth wrung out in hot soapy water.

G

LASS

Hob top. 

Wipe with a cloth wrung out in hot soapy water.  Then dry

with  a  clean  dry  cloth.    You  may  use  a  glass  cleaner,  but

always follow the instructions carefully.

C

AST

 I

RON

Griddle, pansupports

Wipe with a cloth wrung out in hot soapy water.  Dry with a

clean cloth.  Do not wash in a dishwasher.

Always:  Turn  off  the

electricity 

supply

before cleaning. 

Summary of Contents for S5-G700E

















Reviews: