background image

Copyright@2016 HeliPal.com. All Rights Reserved 

 

DISCLAIMER 
 

Please  read  this  disclaimer  carefully  before  using  this  product.  This  product  is  a 
hobby  with  motors  but  not  a  toy  which  is  not  suitable  for  people  under  the  age  of 
18. By using this product, you hereby agree to this disclaimer and signify that you 
have  read  them  fully.  You  agreed  that  you  are  responsible  for  your  own  conduct 
and content while using this product, and for any consequences thereof. 
 
Before you fly the drone 
 
1)

 

Make  sure  all  connections  are  good,  and  keep  children  and  animals  away 
during flying, firmware update, system calibration and parameter setup. 

 
2)

 

Always  fly the drone away  from  unsafe conditions, such as obstacles, crowds, 
high-voltage lines, etc. 

 
3)

 

Do  not  use  in  bad  weathers  such  as  rainy  day,  snow,  windy  (more  than 
moderate breeze), hail, lighting, tornadoes, hurricanes etc. 

 
4)

 

Check  whether  the  propellers  and  the  motors  are  installed  correctly  and  firmly 
before flight. Make sure the rotation direction of each propeller is correct. 

 
5)

 

Check whether all parts of the drone are in good condition before flight. Do not 
fly with aging or broken parts. 

 
6)

 

Never overcharge LiPo batteries. Do not charge above 4.2V per cell. When the 
battery is fully charged, disconnect it from the charger. Never leave the battery 
charger unattended during charging.  

 
7)

 

Never discharge batteries to below 3.3V per cell 

 
8)

 

Remove batteries when not using the drone. 

 

Summary of Contents for Ninja 250











Reviews: