Storm AXS DS601K20 Engineering Manual Download | Manualshive

Page: 3 / 12

background image

Engineering Manual for

AXS Series S60 Keypads

S60 Engineering Manual

Page 3 of 12

www.storm-interface.com

Rev 1.6 May 2016

© Copyright Storm Interface. 2016. All rights reserved

Exploded View

The product is supplied as below, note this product is designed to be installed onto a smooth surface (not a brick wall).

FRONT ASSEMBLY

REAR PLATE (with sticky gasket)

FITTING KIT & DATASHEET

CABLE

ENTRY

PORT

TAMPER

CONNECTION

2 X POZI CSK SCREW #8
x ¾ inch

1 X RELEASE TOOL

«
1
2
3
4
5
...
»

Summary of Contents for DS601K20













Reviews:

No comments

Related manuals for DS601K20

Brand: Egardia Pages: 4

Brand: AEA Pages: 13

Brand: bolid Pages: 64

Brand: ANXELL Pages: 5

Brand: Anviz Pages: 32

Brand: NAPCO Pages: 16

Magnum Alert RP2000LCD

Brand: NAPCO Pages: 28

Brand: Tyco Pages: 64

Brand: Gecko Pages: 30

AMX FG2102-06L-BL

Brand: Harman Pages: 43

Brand: King gates Pages: 4

Brand: Russound Pages: 2

Brand: Vimar Pages: 12

Dolphin DOLKWP318LIPSQ

Brand: Transmitter Solutions Pages: 4

Brand: Rokonet Pages: 8

Innovating FRENIC-HVAC

Brand: Fuji Electric Pages: 2

Brand: Electia Pages: 23

Brand: Extel Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands