LED Low Voltage
30 ft. Linkable
Spotlight Kit
w/ 45W Dusk to Dawn
Transformer
MODEL No:
LL-200-30D
PACKAGE CONTENTS
ADDITIONAL WARNINGS
INSTALLATION
3 YEAR LIMITED WARRANTY
This product is guaranteed against failure due to factory defects in materials or workmanship for three (3) years from the date of
purchase. This warranty is non-transferable and applies only to the original owner. Proof of purchase is required for repair or
replacement. This warranty does not cover normal wear of parts or damage resulting from any misuse of the product. Misuse of
the product includes, but is not limited to: washing the product, using in extreme weather conditions, opening the product, or
trying to remodel the product. Important: this warranty is only valid if the product has been purchased through an authorized
reseller.
WARNINGS
WARNING: Do NOT look directly at LED light sources.
This fixture is IP65 rated and therefore is suitable for
indoor and outdoor use in wet locations.
SAFETY AND PRECAUTIONS
1. Suitable for indoor and outdoor wet locations.
2. Do NOT look directly at LED light sources.
3. The LED modules used in this fixture are not serviceable.
4. This product is inspected prior to shipping. Do not use if product is cracked, broken or missing parts.
5. Suitable for use in operating environments ranging between -13° to 122°F (-25° to 50° C). Lifetime of this product may be
reduced with prolonged exposure to extreme temperatures.
6. Do not anchor cord with staples, nails, or similar objects to avoid puncture and damage to the cord.
7. Do not cover this product as the covering may cause the lights to overheat or ignite.
8. Do not use if there is any damage to the light or cord insulation. Inspect periodically.
9. Do not install the lighting near flammable liquids.
10. Do not install on doors or gates where repeated flexing can occur.
11. For outdoor installation, a Ground Fault Interrupting Circuit (GFCI) outlet must be used.
12. Do not hang objects from cords.
13. Do not use dimmers or in-line cord switches.
14. Ensure all connections and the cap on the last segment of cord is tightly secured to prevent water entry.
15. Unplug cord from outlet prior to adding additional strands.
CUSTOMER SERVICE
For questions regarding this product, please contact us at 303.652.6164, M-F 7am - 4pm MT or e-mail us at
[email protected].
TROUBLESHOOTING GUIDE
CLEANING INSTRUCTIONS
Using a soft cloth, clean the fixture using a mild, non-abrasive glass cleaner. DO NOT use solvents. DO NOT use cleaners
containing abrasive agents. NEVER spray liquid cleaner directly onto the light or LED.
Problem
Probable Cause
Solution
Light comes on during the
daylight hours.
Light cycles ON and OFF
continuously (strobe light effect).
1. Dusk-to-dawn sensor is
detecting reflected light
from the landscape light.
1. Change the position of the light head.
Reposition light away from the reflecting surface.
2. Place a small piece of black electrical tape over
the bottom half of the dusk-to-dawn sensor.
3. Move the light to a different location where the
results are better.
1. Fixture is located in a shaded
area; dusk-to-dawn sensor is
detecting darkness.
1. Shine a light at the dusk-to-dawn sensor.
If the landscape light immediately shuts off,
then the fixture is located in an area that is
too dark to allow enough light to enter the
sensor. The light will need to be relocated.
Circuit breaker trips or fuse blows
when light is turned on.
1. Discontinue use
immediately.
1. Call customer service at 303.652.6164.
2. Call an electrician.
Individual light goes out.
1. Loose connection.
2. Damaged light or cord.
1. Check connection.
2. Discontinue use immediately.
Call customer service at 303.652.6164.
WARNING: Avoid using this product in the immediate vicinity of highly
flammable materials, liquids and gases.
WARNING: DO NOT alter or disassemble any of the parts of this fixture. It is
completely enclosed and does not contain replaceable or serviceable parts.
LED Facts:
Lumens: 600 (200 each head)
Color Temperature: 5000K
CRI: 70
Efficacy (Lumens Per Watt): 90
Rated Watts: 9W (Total Kit)
LED Life: 50,000 hours
Operating temperature: -13° to 122°F (-25° to 50° C)
Power Factor: 0.9
Product Features:
Link Up to 5 Sets (15 total heads (45 total watts))
Operating Voltage: 110-240v
Operating Time On: 4-6-8 Hours
Quick connect with movable heads
Cord Type: 18/2 SJTW
Total cord length: 30 ft.
1
4
3
2
3x
Light
Head
1x
Dusk to Dawn
45W Transformer
3 ft. Cord
Quick
Adapter
Plug
Quick Connector
End Cap
Shroud
Quick Connector
1x
30 ft. Main Cord
Collar Ring
Friction Lock
3x
Ground
Stake
2x
Wood
Screws
Thumbscrew
Dusk-to-Dawn
Sensor
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
The user is cautioned that any changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1) Reorient or relocate the receiving antenna. 2) Increase the separation between the equipment and receiver. 3) Connect the equipment into
an outlet on a circuit different from that of the receiver. 4) Consult the dealer or an experienced radio/TV technician for help.
1. Plug the dusk to
dawn timer into a
GFCI protected
outlet and attach
it to the surface
using the
included wood
screws (Fig. 1).
2. Each connection is made up of a connector (Fig. 2) and
quick connector
(Fig. 3). The quick connectors and connectors
are only designed to connect one way.
5.
Remove the thumbscrews from the stakes (Fig. 10). Line up the flat side of the ground stake with the friction lock, against the
friction lock on the back of the light head (Fig. 11). Fasten both pieces together with the thumb screw (Fig. 12).
6.
The light heads can be positioned from horizontal to straight up (Fig. 13). Loosen the thumbscrew to reposition the light head
to the proper angle.
7. An end cap must be securely attached at
the end of the main cord. The main cord is
now ready to be plugged in.
1. Up to 5 sets of lights (15 heads) can be hooked up to one power control unit. An end
cap must be securely attached at the end of the cord before plugging in.
4.
Attach the light heads to the main cord. There are 3 jacks spaced along the length of the main cord, plug in the quick
connectors from the light heads into the connectors in the main cord (Fig. 7). Fully insert the quick connectors into the power
adapters (Fig. 8). Tighten the collar ring firmly to keep water out (Fig. 9).
WARNING: DO NOT use with extension cords near water or wherever water
may accumulate.
WARNING: This product has a grounded plug (two contact blades and a grounding
prong) as a feature to reduce the risk of electric shock. The plug is fashioned to
only fit in a grounded outlet one way. If it does not fit, contact a qualified electrician.
Never use with an extension cord unless plug can be fully inserted. DO NOT ALTER THE
PLUG OR CORD.
WARNING: ONLY use in a GFCI protected outlet for outdoor utilizations.
(Fig. 1)
(Fig. 2)
(Fig. 3)
(Fig. 10)
(Fig. 7)
(Fig. 11)
(Fig. 8)
(Fig. 12)
(Fig. 9)
(Fig. 13)
INSTALLATION (Continued)
INSTALLING ADDITIONAL UNITS
Push stakes into ground and aim light.
(Fig. 4)
(Fig. 5)
(Fig. 6)
3.
Attach the 30 ft. main cord to the
dusk to dawn timer (
Fig. 4). Fully insert the connector into the quick connector (Fig. 5). Tighten
the collar ring firmly to keep water out (Fig. 6). Unroll the cord and connect the light heads and place in desired location.
Quick Connector
Connector
1. The lights will automatically
turn on at dusk. The adjustable
timer is located on the side of
the transformer, this will
determine how long the lights
stay on. Set the switch to either
4H (4 hours), 6H (6 hours) and
8H (hours) (Fig. 14).
INSTALLATION (Continued)
(Fig. 14)
Revision Date: 03-08-2018
4-6-8
Hour
Switch
4.5 in
.
11,43 cm
3.25 in
.
8,3 cm
6.25 in.
15,87 cm
