LED Low Voltage
25 ft. Linkable
Spotlight Kit
with 12W Dusk to Dawn
Transformer
MODEL No:
LL-100-25D
PACKAGE CONTENTS
ADDITIONAL WARNINGS
INSTALLATION
3 YEAR LIMITED WARRANTY
This product is guaranteed against failure due to factory defects in materials or workmanship for three (3) years from the date of
purchase. This warranty is non-transferable and applies only to the original owner. Proof of purchase is required for repair or
replacement. This warranty does not cover normal wear of parts or damage resulting from any misuse of the product. Misuse of
the product includes, but is not limited to: washing the product, using in extreme weather conditions, opening the product, or
trying to remodel the product. Important: this warranty is only valid if the product has been purchased through an authorized
reseller.
WARNINGS
This fixture is IP65 rated and therefore is suitable for
indoor and outdoor use in wet locations.
SAFETY AND PRECAUTIONS
1. Suitable for indoor and outdoor wet locations.
2. Do NOT look directly at LED light sources.
3. The LED modules used in this fixture are not serviceable.
4. This product is inspected prior to shipping. Do not use if product is cracked, broken or missing parts.
5. Suitable for use in operating environments ranging between -13° to 122°F (-25° to 50° C). Lifetime of this product may be
reduced with prolonged exposure to extreme temperatures.
6. Do not anchor cord with staples, nails, or similar objects to avoid puncture and damage to the cord.
7. Do not cover this product as the covering may cause the lights to overheat or ignite.
8. Do not use if there is any damage to the light or cord insulation. Inspect periodically.
9. Do not install the lighting near flammable liquids.
10. Do not install on doors or gates where repeated flexing can occur.
11. For outdoor installation, a Ground Fault Interrupting Circuit (GFCI) outlet must be used.
12. Do not hang objects from cords.
13. Do not use dimmers or in-line cord switches.
14. Ensure all connections and the cap on the last segment of cord is tightly secured to prevent water entry.
15. Unplug cord from outlet prior to adding additional strands.
CUSTOMER SERVICE
For questions regarding this product, please contact us at 303.652.6164, M-F 7am - 4pm MT or e-mail us at
[email protected].
TROUBLESHOOTING GUIDE
CLEANING INSTRUCTIONS
Using a soft cloth, clean the fixture using a mild, non-abrasive glass cleaner. DO NOT use solvents. DO NOT use cleaners
containing abrasive agents. NEVER spray liquid cleaner directly onto the light or LED.
Problem
Probable Cause
Solution
Light comes on during the
daylight hours.
Light cycles ON and OFF
continuously (strobe light effect).
1. Dusk-to-dawn sensor is
detecting reflected light
from the landscape light.
1. Change the position of the light head.
Reposition light away from the reflecting surface.
2. Place a small piece of black electrical tape over
the bottom half of the dusk-to-dawn sensor.
3. Move the light to a different location where the
results are better.
1. Fixture is located in a shaded
area; dusk-to-dawn sensor is
detecting darkness.
1. Shine a light at the dusk-to-dawn sensor.
If the landscape light immediately shuts off,
then the fixture is located in an area that is
too dark to allow enough light to enter the
sensor. The light will need to be relocated.
Circuit breaker trips or fuse blows
when light is turned on.
1. Discontinue use
immediately.
1. Call customer service at 303.652.6164.
2. Call an electrician.
Individual light goes out.
1. Loose connection.
2. Damaged light or cord.
1. Check connection.
2. Discontinue use immediately.
Call customer service at 303.652.6164.
LED Facts:
Lumens: 300 (100 each head)
Color Temperature: 5000K
CRI: 80
Efficacy (Lumens Per Watt): 90
Rated Watts: 4.5W (Total Kit)
LED Life: 50,000 hours
Operating temperature: -13° to 122°F (-25° to 50° C)
Beam Angle: 80°
Power Factor: 0.7
Product Features:
Link Up to 12 Watts Total, (8) 100 Lumen Spotlights
Operating Voltage: 120v
Quick connect with movable heads
Cord Type: 18/2 SPT-2W
Total cord length: 25 ft.
1
4
3
3x
Light
Head
1 x
Dusk to Dawn
12W Transformer
3 ft. Cord
Quick Adapter
Quick Connector
2x
End Cap
Shroud
Quick Connector
1x
25 ft.
Main
Cord
Collar Ring
Friction Lock
3x
Ground
Stake
Thumbscrew
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
The user is cautioned that any changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1) Reorient or relocate the receiving antenna. 2) Increase the separation between the equipment and receiver. 3) Connect the equipment into
an outlet on a circuit different from that of the receiver. 4) Consult the dealer or an experienced radio/TV technician for help.
1. The dusk to dawn timer should be
plugged into a GFCI protected outlet, but
do not plug in the dusk-to-dawn
transformer until the installation is
complete(Fig. 1).
5.
Remove the thumbscrews from the stakes (Fig. 10). Line up the flat side of the ground stake with the friction lock (Fig. 11) against the friction
lock on the back of the light head (Fig. 12). Fasten both pieces together with the thumb screw (Fig. 13).
6.
The light heads can be positioned from horizontal to straight up (Fig. 14). Loosen the thumbscrew to reposition the light head to the proper
angle.
7. An end cap must be securely attached at
the end of the main cord
(Fig. 15)
(The dusk
to dawn transformer is ready to be
plugged in).
1. Up to (8) 100 Lumen Spotlights (12 Watts total) can be hooked up to one power
control unit. An end cap must be securely attached at the end of the cord before
plugging in.
4.
Attach the light heads to the main cord. There are 3 jacks spaced along the length of the main cord, plug in the quick connectors from the
light heads into the connectors in the main cord (Fig. 7). Fully insert the quick connectors into the power adapters (Fig. 8). Tighten the collar
ring firmly to keep water out (Fig. 9).
3.25 in
.
8,25 cm
2.5 in
.
6,4 cm
5 in.
12,7 cm
WARNING: DO NOT use with extension cords near water or wherever water
may accumulate.
WARNING: This product has a polarized plug (one contact blade is wider than the
other) as a feature to reduce the risk of electric shock. The plug is fashioned to
only fit in a grounded outlet one way. If it does not fit, contact a qualified electrician.
Never use with an extension cord unless plug can be fully inserted. DO NOT ALTER THE
PLUG OR CORD.
(Fig. 10)
(Fig. 7)
(Fig. 11)
(Fig. 12)
(Fig. 8)
(Fig. 13)
(Fig. 9)
(Fig. 14)
(Fig. 15)
INSTALLATION (Continued)
INSTALLING ADDITIONAL UNITS
Push stakes into ground and aim light.
(Fig. 4)
(Fig. 5)
(Fig. 6)
3.
Attach the 25 ft. main cord to the
dusk to dawn timer (
Fig. 4). Fully insert the connector into the quick connector (Fig. 5). Tighten the collar ring
firmly to keep water out (Fig. 6). Unroll the cord and connect the light heads and place in desired location.
WARNING: Do NOT look directly at LED light sources.
WARNING: ONLY use in a GFCI protected outlet for outdoor utilizations.
WARNING: Avoid using this product in the immediate vicinity of highly
flammable materials, liquids and gases.
WARNING: DO NOT alter or disassemble any of the parts of this fixture. It is
completely enclosed and does not contain replaceable or serviceable parts.
1. The lights will automatically
turn on at dusk (Fig. 16).
INSTALLATION (Continued)
(Fig. 16)
Revision Date: 01-11-2018
(Fig. 1)
2. Each connection is made up of a connector (Fig. 3) and quick connector
(Fig. 4). The quick
connectors and connectors are only designed to connect one way.
(Fig. 3)
(Fig. 4)
Quick Connector
Connector
2
Check all connections, make sure they are all on tight to prevent water from entering the connections
Plug
Dusk-to-Dawn
Sensor
