PACKAGE CONTENTS
ADDITIONAL WARNINGS
3 YEAR LIMITED WARRANTY
This product is guaranteed against failure due to factory defects in materials or workmanship for three (3) years from the date of
purchase. This warranty is non-transferable and applies only to the original owner. Proof of purchase is required for repair or replace-
ment. This warranty does not cover normal wear of parts or damage resulting from any misuse of the product. Misuse of the product
includes, but is not limited to: washing the product, using in extreme weather conditions, opening the product, or trying to remodel the
product. Important: this warranty is only valid if the product has been purchased through an authorized reseller. Returns and/or warranty
replacements must be processed at the original place of purchase.
WARNINGS
This fixture is
rated for damp
location use.
SAFETY AND PRECAUTIONS
1. Suitable for damp location use.
2. Do
NOT
install over stoves.
3. Do
NOT
look directly at LED light sources.
4. The LED modules used in this fixture are not serviceable.
5
. This product is inspected prior to shipping.
Do not use if product is cracked, broken or missing parts.
6. Suitable for use in operating environments ranging between -4° to 113°F (-20° to 45° C).
7. Electrical requirements can be found on back of the fixture.
8. Do not mount where fixture may come in contact with water.
• Shut off power to electrical outlet before installing or servicing this fixture.
CUSTOMER SERVICE
For questions regarding this product, please e-mail us at
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the user’s authority to operate the equipment. The user is cautioned that any changes or modifications not
expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures: 1) Reorient or relocate the receiving antenna. 2) Increase the separation between the equipment and
receiver. 3) Connect the equipment into an outlet on a circuit different from that of the receiver. 4) Consult the dealer or an experienced radio/TV technician for help.
TROUBLESHOOTING GUIDE
CLEANING INSTRUCTIONS
Disconnect power to fixture before cleaning. Using a soft cloth, clean the fixture using a mild, non-abrasive glass cleaner. DO NOT use
solvents. DO NOT use cleaners containing abrasive agents. NEVER spray liquid cleaner directly onto the LEDs, fixture or wiring.
Before starting work to connect the fixture, shut off power supply at the circuit breaker panel to avoid electrical shock.
Fixture does not turn on.
Problem
Probable Cause
Solution
Circuit breaker trips or fuse blows
when light is turned on.
1. Faulty switch.
2. Power is off.
1. Discontinue use
immediately.
1. Test switch or replace it.
2. Verify power supply is on.
1. Call an electrician.
DIMMING
• DO NOT USE THIS FIXTURE WITH DIMMERS.
Doing so will void the warranty of this product.
LED Facts:
FRPF (700-800nm):
PPF (400-700nm):
Blue PF (400-500nm):
Red PF (600-700nm):
LED Life: 50,000 hours
Operating Voltage: 120v
Cord Type: .18/3 SVT
1
4
3
2
46.5 in.
WARNING:
Do
NOT
look directly at LED light sources.
WARNING:
Use only in 120v, 60Hz circuits.
WARNING:
This product is not wateproof.
WARNING: TO AVOID ELECTRIC SHOCK,
DISCONNECT POWER BEFORE INSTALLING
WARNING:
DO NOT alter or disassemble the fixture it is completely
enclosed and does not contain replaceable or serviceable parts.
WARNING:
Before installation, plug in fixture to a 120v, 60Hz electrical
outlet to check for proper operation. Then, unplug and begin the installation.
WARNING: BURN HAZARD!
Light fixture is hot, allow cooling time
before touching.
CAUTION:
Personal injury can occur, along with damage to
the fixture and/or mounting surface may result if the fixture is
pulled from the surface. To prevent premature failure from over-
heating, fixture should only be installed in environments where the
operating temperatures are between -4° to 113°F (-20° to 45° C).
WARNING:
This product may represent a possible shock or fire hazard
if improperly installed or mounted. Products should be installed following
these instructions, local electrical codes and/or the current National Electric Code
(NEC).
WARNING:
This product has a grounded plug (two contact
blades and a grounding prong) as a feature to reduce the risk of
electric shock. The plug is fashioned to only fit in a grounded outlet
one way. If it does not fit, contact a qualified electrician. Never use
with an extension cord unless plug can be fully inserted.
DO NOT
ALTER THE PLUG OR CORD.
OPERATION
5 ft. 18/3 SVT Cord
INSTALLATION INSTRUCTIONS
Install the fixture between 12 in. to 39 in. above
the top of the plants
(Fig. 1).
Revision Date: 06-30-2020
2x
Mounting clip
with cables
INSTALLATION INSTRUCTIONS
12-39 in.
above plant tops
Install the fixture before plugging it into an electrical outlet. Be sure to locate fixture within 5 ft. of the power supply.
Before installation, cut off power to the electrical outlet.
1. Install the mounting clip with cable to the top side of the fixture along the mounting track that the runs most of the length of the fixture
(Fig. 2)
.
Lower the clip onto the track. Hook to one side
(Fig. 3)
and press down
(Fig. 4)
until the clip snaps into place
(Fig. 5)
. Attach the hanging cables
to the ceiling (The actual mounting of the hanging cables to the ceiling or stand is not covered in these instructions). The mounting clips with
cables are only designed to hold the weight of the fixture safely.
2. Installation is now complete. Plug the fixture in.
Fig. 2
Fig. 1
Fig. 3
Fig. 4
Fig. 5
Fig.6
Fig.7
1.5 in.
1.62 in.
TOP
SIDE
Snap on track for mounting clips
Snap on hanger hook track
Pull chain
Grounded
linking outlet
Diffuser
MODEL No:
GR-SHP4L
RECOMMENDED
It is recommended the power cord be secured to one of the
hanging support chains with cable ties (not included)
(Fig. 6)
.
This fixture can be linked with #GR-SHP2L and #GR-SHP4L fixtures and up to a maximum of 228 total watts.
LINKING ADDITIONAL UNITS
1. To link additional lights, unplug the first fixture the additional light will link to. Repeat Step 1 for the additional fixtures. A maximum lights
connected on one string of lights
MUST NOT EXCEED A TOTAL OF 2A
. Plug each additional light into the preceding unit
(Fig. 10)
. Repeat as
necessary. Restore power.
1. Pull the chain switch down to turn the light on and
off
(Fig 7)
.
NOTE:
For optimal results, the maximum distance between any two linking fixtures should not exceed 12 inches,
especially mounted over longer plant beds.
4 Ft. LED
Linkable Grow
Strip Light
Set the height of the grow light so the center of the
light shining down does not create a “hot spot”, the
light will be too focused on a specific area and may
decrease the light absorption in the plants at the
perimeter of the coverage area.
