Blu
Skye
® Bluetooth®RSM
User Guide
Table of Contents
1. Package contents
2. Overview
3.
Initial Setup
4. LED Signals
5.
Operation Instructions
6. Care and Maintenance
7. Disclaimers
8.
Regulatory Certifications
1) Package Contents
Blu
Skye
® Bluetooth Remote Speaker Microphone
(RSM),
Pro
Strap
™
lanyard, Charger, User Guide
2) Overview
1. Secondary PTT / Emergency Button
2. Primary PTT Button
3.
RampClik
™
Volume Button
4. 3.5mm Audio Accessory Port
5. Charging Port
6. Call function button
7. Charging / Mobile cradle contacts
8. Power / Pairing button
9. LED Indicator
10. Rotating Belt Clip
11 Lanyard / Cable Restraint
3) Initial Setup
Power on:
While the RSM is off, press and hold the
Power button for three seconds. A low-mid two
tone beep and two blue LED flashes will occur.
Power Off:
Press and hold the Power button for
three seconds. One beep will occur for each second
held to alert you the RSM will power off. The RSM
will emit a mid-low two tone beep and the LED
will flash red twice as it powers off. If the button
is released before three seconds have passed, the
RSM will not power off.
Pairing Mode:
While the RSM is off, press and hold
the Power button for six seconds to enter pairing
mode. A mid-high two tone beep and continuous
red/blue LED flashes will occur. Follow instructions
for your LMR or phone to complete pairing. Use
passcode “
0000”
if required. Once the RSM is
paired and connected to a device, the LED will flash
blue every three seconds.
Kenwood LMR Pairing: When pairing with a Ken-
wood radio, Make sure the RSM is set to Configu
-
ration #5. Follow the pairing procedure as normal.
When the RSM begins playing Star Wars’ Imperial
March song, press the top button to complete
pairing.
If the RSM is not put into Pairing Mode at Power
On, it will attempt to reconnect to the last device it
was paired with. If the RSM can’t connect, the RSM
will show a disconnected state by flashing a red
LED once every three seconds.
If the connection between the RSM and host device
is lost, the RSM will emit two low tone beeps and
the LED will flash red once every three seconds.
NOTE: Pairing only needs to be performed when
connecting to a new device for the first time or after
unpairing from the host.
4) LED Signals
Your Stone Mountain
Blu
Skye
™
uses a Tri-color LED
(red, blue, and green). Different light combinations
represent different states as described below.
Power off:
Two blue flashes
Power Off:
Two red flashes
Pairing Mode:
Continuous alternating red and blue
flashes
Connected:
One blue flash every three seconds
Powered On, Not Connected:
One red flash every
three seconds
Boot Sequence:
Two sets of red, blue, and green
flashes.
Low Battery:
One amber flash added to the current
state (for example, blue/amber or red/amber)
Charging:
One green flash added to the current
state (for example blue/green or red/green)
**Charing status will not be displayed while the
unit is powered off and charging**
5) Operating Instructions
PTT Call:
Press and hold the PTT button to make a
PTT call. This requires a compatible LMR or PoC app
with service.
Emergency Operation:
Depending on your device
or PoC app, the top button can be designated as an
Emergency button. The top button will be designat-
ed as a secondary PTT if no Emergency function is
supported by the host or app.
Volume Control:
To increase the volume level,
press and hold the
RampClik
™
Volume button. The
volume level will increase and will beep once for
each step.
To decrease the volume level, briefly press and
release
the
RampClik
™
Volume button. Each press/
release of the button will decrease the voume level
by one step and will beep once at each step.
Phone Call Control:
To answer an incoming call,
briefly press and release the Call Function button.
To reject an incoming call, hold the Call Function
button for at least one second. To end an ongoing
call, briefly press and release the Call Function
button.
Battery Monitoring:
When the battery voltage falls
to a critical level, the speaker mic will emit one
low beep. A yellow LED flash will be added to its
current state.
Hard Reset:
If abnormalities occur with the speaker
mic, reset it by pressing and holding the Power and
PTT buttons for four seconds. The unit will undergo
its boot sequence, afterwhich it will power down.
The unit should resume normal functionat the next
Power On.
6) Care and Maintenance
Power Management:
The product is powered by a
rechargeable Li-Ion battery. Depending upon the
conditions of use, the battery should last several
hundred recharge cycles. Over time you may
notice significantly shorter battery life where your
RSM can only be powered for a few hours and re-
quires more frequent charging. The battery should
be replaced when this occurs. While genuine Stone
Mountain replacement batteries are available, it is
highly recommended the unit be returned to Stone
Mountain or a Stone Mountain Authorized Service
Center for battery replacement to ensure proper
and safe installation. Contact Stone Mountain to
obtain a Return Maintenance Authorization (RMA)
number prior to any such return.
Only use the supplied charger to recharge your
RSM. Unauthorized chargers may damage the
unit and void the device’s warranty. Unplug the
charger when not in use. Do not leave your
RSM connected to the charger for longer than
necessary, as overcharging will shorten the overall
life of the battery.
If left unused a fully charged RSM will discharge
itself over time.
Temperature extremes may adversely affect the
lifetime and ability of the battery to charge. Always
try to keep the RSM between 59°F and 77°F (15°C
and 25°C). A device with a hot or cold battery
may not work for a while even when the battery is
fully charged. Battery performance is particularly
limited in temperatures below freezing.
7) Disclaimers
DISCLAIMER OF WARRANTIES:
TO THE
FULLEST EXTENT PERMISSIBLE PURSUANT TO
APPLICABLE LAW, STONE MOUNTAIN, LTD (“STONE
MOUNTAIN”) DISCLAIMS ALL WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING, BUT NOT
LIMITED TO, WARRANTIES OF PERFORMANCE,
NON-INFRINGEMENT, MERCHANTABILITY, OR
FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE
RISK ARISING OUT OF USE OR PERFORMANCE
OF THE PRODUCT REMAINS WITH YOU. THE
PRODUCT, INFORMATION AND DATA CONTAINED
IN THE PRODUCT AND ANY DOCUMENTATION,
INCLUDING ANY SUPPORT SERVICES OR THE
FAILURE TO PROVIDE SUCH SERVICES, ARE
PROVIDED “AS IS”, WITH ALL FAULTS, ERRORS,
OMISSIONS AND INACCURACIES, AND WITHOUT
WARRANTY OF ANY KIND. STONE MOUNTAIN IS,
UNDER NO CIRCUMSTANCES, RESPONSIBLE FOR
ANY UNAUTHORIZED USE OR MODIFICATION OF
THE PRODUCT. Because some states/jurisdictions
do not allow limitations on how long an implied
warranty lasts, the above limitation may not apply
to you.
LIMITATION OF LIABILITY:
UNDER NO
CIRCUMSTANCES SHALL STONE MOUNTAIN
BE LIABLE FOR ANY LOSSES OR DAMAGES
WHATSOEVER, WHETHER IN CONTRACT,
TORT OR OTHERWISE, FROM THE USE OF, OR
RELIANCE ON, THE PRODUCT. IN NO EVENT
SHALL STONE MOUNTAIN BE LIABLE FOR ANY
DAMAGES OR LOSSES FROM LOSS OF USE, LOSS
OF TIME, INCONVENIENCE, COMMERCIAL LOSS,
LOST PROFITS, BUSINESS INTERRUPTION, LOSS
OF INFORMATION, SAVINGS OR ANY OTHER
PECUNIARY LOSS OR DAMAGES, INCLUDING
WITHOUT LIMITATION DIRECT, INCIDENTAL,
SPECIAL, INDIRECT, EXEMPLARY, CONSEQUENTIAL
OR ANY OTHER TYPE OF DAMAGES ARISING OUT
OF THIS AGREEMENT OR THE USE OR INABILITY TO
USE THE PRODUCT OR ANY SERVICES PROVIDED OR
THE FAILURE TO PROVIDE SERVICES HEREUNDER,
TO THE FULL EXTENT AS MAY DISCLAIMED BY LAW,
EVEN IF STONE MOUNTAIN HAS BEEN ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES. TO
2
1
4 5
3
6
7
9
8
10
11
