STMicroelectronics STM32F405 Reference Manual Download | Manualshive

Page: 942 / 1731

background image

Serial audio interface (SAI)

RM0090

DocID018909 Rev 11

If there is an audio block in the SAI synchronous with the other one, the one which is the
master must be disabled first.

29.16 SAI

DMA

interface

In order to free the CPU and to optimize the bus bandwidth, each SAI audio block has an
independent DMA interface in order to read or to write into the SAI_xDR register (to hit the
internal FIFO). There is one DMA channel per audio block following basic DMA
request/acknowledge protocol.

To configure the audio block to transfer through the DMA interface, set bit DMAEN in the
SAI_xCR1 register. The DMA request is managed directly by the FIFO controller depend of
FIFO threshold level (for more details please refer to Internal FIFOs section). DMA direction
is linked to the SAI audio block configuration:

•

If the audio block is a transmitter, the audio block’s FIFO controller outputs a DMA
request to load the FIFO with data written in the SAI_xDR register.

•

If the audio block is a receiver, the DMA request will concern read operations from the
SAI_xDR register.

Below are the SAI configuration steps followed when DMA is used:
1.

Configure SAI and FIFO Threshold level (in order to specify when the DMA request to
be launched)

2. Configure SAI DMA channel
3. Enable

DMA

4. Enable

SAI

Note:

Before configuring the SAI block, the SAI DMA channel must be disabled.

«
...
940
941
942
943
944
...
»

Summary of Contents for STM32F405




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for STM32F405

imageRUNNER ADVANCE C9075S PRO

Brand: Canon Pages: 20

Brand: IBM Pages: 105

Brand: Jafar Pages: 9

Brand: Samsung Pages: 6

Brand: Samsung Pages: 32

Brand: janitza Pages: 58

Brand: MacDon Pages: 32

Brand: K&K Pages: 6

Brand: Rain Bird Pages: 4

Brand: Rain Bird Pages: 2

Brand: Rain Bird Pages: 140

WeatherSmart RSC600i

Brand: Raindrip Pages: 36

TEMP2000 Series

Brand: Samwontech Pages: 91

Brand: Warren rupp Pages: 18

Brand: Yamaha Pages: 100

traxon e:cue LCE-mx

Brand: Osram Pages: 35

Brand: ECKELMANN Pages: 147

Brand: Squizz Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands