STMicroelectronics STM32F405 Reference Manual Download | Manualshive

Page: 464 / 1731

background image

Digital camera interface (DCMI)

RM0090

DocID018909 Rev 11

Continuous grab mode

In this mode (CM bit = ‘0’ in DCMI_CR), once the CAPTURE bit has been set in DCMI_CR,
the grabbing process starts on the next VSYNC or embedded frame start depending on the
mode. The process continues until the CAPTURE bit is cleared in DCMI_CR. Once the
CAPTURE bit has been cleared, the grabbing process continues until the end of the current
frame.

Figure 77. Frame capture waveforms in continuous grab mode

1. Here, the active state of DCMI_HSYNC and DCMI_VSYNC is 1.
2. DCMI_HSYNC and DCMI_VSYNC can change states at the same time.

In continuous grab mode, you can configure the FCRC bits in DCMI_CR to grab all pictures,
every second picture or one out of four pictures to decrease the frame capture rate.

Note:

In the hardware synchronization mode (ESS = ‘0’ in DCMI_CR), the IT_VSYNC interrupt is
generated (if enabled) even when CAPTURE = ‘0’ in DCMI_CR so, to reduce the frame
capture rate even further, the IT_VSYNC interrupt can be used to count the number of
frames between 2 captures in conjunction with the Snapshot mode. This is not allowed by
embedded data synchronization mode.

15.5.5 Crop

feature

With the crop feature, the camera interface can select a rectangular window from the
received image. The start (upper left corner) coordinates and size (horizontal dimension in
number of pixel clocks and vertical dimension in number of lines) are specified using two 32-
bit registers (DCMI_CWSTRT and DCMI_CWSIZE). The size of the window is specified in
number of pixel clocks (horizontal dimension) and in number of lines (vertical dimension).

Figure 78. Coordinates and size of the window after cropping

DCMI_HSYNC

DCMI_VSYNC

Frame 1 captured

Frame 2 captured

ai15833

CAPCNT

b

it in DCMI_CSIZE

HOFFCNT

b

it in DCMI_CSTRT

ai15834

VST

b

it in DCMI_CSTRT

VLINE

b

it in DCMI_CSIZE

«
...
462
463
464
465
466
...
»

Summary of Contents for STM32F405




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for STM32F405

Brand: Wasp Pages: 16

Brand: Vacon Pages: 64

Brand: Camozzi Pages: 33

Brand: Camozzi Pages: 2

Brand: Camozzi Pages: 64

Brand: Kamstrup Pages: 36

Brand: JFA Electronicos Pages: 29

GRAVIMETRIC AUGER FEEDER MGF-ST

Brand: Maguire Products Pages: 47

Brand: Magtrol Pages: 160

Brand: National Instruments Pages: 40

Brand: National Instruments Pages: 28

Brand: National Instruments Pages: 7

Brand: National Instruments Pages: 22

Brand: T&D Pages: 2

Brand: T&S Pages: 5

Brand: Panasonic Pages: 8

Brand: PESA Pages: 30

Brand: Osram Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands