STMicroelectronics STM32F405 Reference Manual Download | Manualshive

Page: 1474 / 1731

background image

USB on-the-go high-speed (OTG_HS)

RM0090

DocID018909 Rev 11

1.

Program the following fields in the Global AHB configuration (OTG_HS_GAHBCFG)
register:
–

DMA mode bit

–

AHB burst length field

–

Global interrupt mask bit GINT = 1

–

RxFIFO nonempty (RXFLVL bit in OTG_HS_GINTSTS)

–

Periodic TxFIFO empty level

2. Program the following fields in OTG_HS_GUSBCFG register:

–

HNP capable bit

–

SRP capable bit

–

FS timeout calibration field

–

USB turnaround time field

3. The software must unmask the following bits in the GINTMSK register:

OTG interrupt mask
Mode mismatch interrupt mask

4. The software can read the CMOD bit in OTG_HS_GINTSTS to determine whether the

OTG_HS controller is operating in host or peripheral mode.

35.13.2 Host

initialization

To initialize the core as host, the application must perform the following steps:
1.

Program the HPRTINT in GINTMSK to unmask

2. Program the OTG_HS_HCFG register to select full-speed host
3. Program the PPWR bit in OTG_HS_HPRT to 1. This drives V

BUS

on the USB.

4. Wait for the PCDET interrupt in OTG_HS_HPRT0. This indicates that a device is

connecting to the port.

5.  Program the PRST bit in OTG_HS_HPRT to 1. This starts the reset process.
6.  Wait at least 10 ms for the reset process to complete.
7.  Program the PRST bit in OTG_HS_HPRT to 0.
8.  Wait for the PENCHNG interrupt in OTG_HS_HPRT.
9.  Read the PSPD bit in OTG_HS_HPRT to get the enumerated speed.
10.  Program the HFIR register with a value corresponding to the selected PHY clock 1.
11.  Program the FSLSPCS field in OTG_FS_HCFG register according to the speed of the

detected device read in step 9. If FSLSPCS has been changed, reset the port.

12. Program the OTG_HS_GRXFSIZ register to select the size of the receive FIFO.
13. Program the OTG_HS_GNPTXFSIZ register to select the size and the start address of

the nonperiodic transmit FIFO for nonperiodic transactions.

14. Program the OTG_HS_HPTXFSIZ register to select the size and start address of the

periodic transmit FIFO for periodic transactions.

To communicate with devices, the system software must initialize and enable at least one
channel.

«
...
1472
1473
1474
1475
1476
...
»

Summary of Contents for STM32F405




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for STM32F405

Brand: Manfrotto Pages: 16

Brand: Casambi Pages: 2

Brand: IBCcontrol Pages: 16

NuMicro M252 Series

Brand: Nuvoton Pages: 38

External Joystick

Brand: Quickie Pages: 4

TECSource 5400 Series

Brand: Arroyo Instruments Pages: 60

Brand: SainSmart Pages: 17

Brand: DAAB Pages: 60

Brand: BILDA Pages: 2

MCE Lasers DUO 2 v2

Brand: MOBA Pages: 60

Brand: KELD Pages: 2

Brand: Viessmann Pages: 12

SPACOMMAND CP3800 Series

Brand: Pentair Pages: 36

Brand: tecatlantis Pages: 68

R7G4HEIP-6-DC16B

Brand: M-system Pages: 6

CONPROSYS nano CPSN-CNT-3201I

Brand: Contec Pages: 49

SAFEMASTER UF 6925

Brand: DOLD Pages: 36

MECHATROLINK Sigma 2 Series

Brand: YASKAWA Pages: 257

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands