STMicroelectronics STM32F405 Reference Manual Download | Manualshive

Page: 133 / 1731

background image

DocID018909 Rev 11

RM0090

Power controller (PWR)

149

5.3.5 Stop

mode

(STM32F42xxx and STM32F43xxx)

The Stop mode is based on the Cortex

®

-M4 with FPU deepsleep mode combined with

peripheral clock gating. The voltage regulator can be configured either in normal or low-
power mode. In Stop mode, all clocks in the 1.2 V domain are stopped, the PLLs, the HSI
and the HSE RC oscillators are disabled. Internal SRAM and register contents are
preserved.

In Stop mode, the power consumption can be further reduced by using additional settings in
the PWR_CR register. However this will induce an additional startup delay when waking up
from Stop mode (see

).

Mode exit

If WFI or Return from ISR was used for entry:

Any EXTI lines configured in Interrupt mode (the corresponding EXTI
Interrupt vector must be enabled in the NVIC). The interrupt source can
be external interrupts or peripherals with wakeup capability. Refer to

Table 61: Vector table for STM32F405xx/07xx and STM32F415xx/17xx
on page 374

Table 62: Vector table for STM32F42xxx and

If WFE was used for entry and SEVONPEND = 0

Any EXTI lines configured in event mode. Refer to

Section 12.2.3:

Wakeup event management on page 382

If WFE was used for entry and SEVONPEND = 1:
– Any EXTI lines configured in Interrupt mode (even if the corresponding

EXTI Interrupt vector is disabled in the NVIC). The interrupt source can
be an external interrupt or a peripheral with wakeup capability. Refer to

Table 61: Vector table for STM32F405xx/07xx and STM32F415xx/17xx
on page 374

Table 62: Vector table for STM32F42xxx and

– Wakeup event: refer to

Section 12.2.3: Wakeup event management on

Wakeup latency

Table 26: Stop operating modes (STM32F405xx/07xx and
STM32F415xx/17xx)

Table 27. Stop mode entry and exit (for STM32F405xx/07xx and STM32F415xx/17xx)

Stop mode

Description

«
...
131
132
133
134
135
...
»

Summary of Contents for STM32F405




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for STM32F405

ControlMaster CM15

Brand: ABB Pages: 28

Brand: Vacon Pages: 64

Brand: Eaton Pages: 86

Brand: Badger Basket Pages: 3

Brand: BADLANDS Pages: 2

Brand: Calsense Pages: 74

VARIVENT D Series

Brand: GEA Pages: 78

Brand: GEA Pages: 96

Brand: GEA Pages: 66

Brand: UNI Pages: 21

Brand: OBSIDIAN CONTROL SYSTEMS Pages: 13

Brand: Rain Bird Pages: 4

Brand: Rain Bird Pages: 2

Brand: Rain Bird Pages: 140

WeatherSmart RSC600i

Brand: Raindrip Pages: 36

Brand: Radionics Pages: 14

Brand: Danfoss Pages: 16

Consolidated 2900-40 Series

Brand: Baker Hughes Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands