STMicroelectronics SPEAr300 Reference Manual Download Page 581 | Manualshive

Page: 581 / 844

background image

RM0082

LS_Fast IrDA controller

Doc ID 018672 Rev 1

26.5.7 IrDA_DV

register

The IrDA_DV (Divider) is a RW register which allows to set the clock divider within the baud
generation unit (

Section 26.3.5: Baud rate generation unit on page 574

) to get the

en_symb

and

en_pulse

signals. This register should only be modified when the FIrDA controller is

disabled by clearing the bit RUN of the IrDA_CON register. The IrDA_DV bit assignments
are given in

Table 501.

IrDA_PARA register bit assignments

Bit

Name

Reset value Description

[31:28]

Reserved

-

Read: undefined. Write: should be zero.

[27:16]

MNRB

12’h046

Maximum number of received bytes.

This 12 bit field indicates the maximum number of
received bytes, according to the encoding:

– 12‘b000001000110 = 70 bytes (default)

– 12‘b000010000110 = 134 bytes

– 12‘b000100000110 = 262 bytes

– 12‘b001000000110 = 518 bytes

– 12‘b010000000110 = 1030 bytes

– 12‘b100000000110 = 2054 bytes

Note: In FIR mode, the effective maximum number of
received bytes is data size + 6 bytes, including the
information byte, the address and control byte, and
the 4 CRC bytes.

Note: This field should be programmed according to
the negotiated data size (see IrLAP specification).

[15:08]

Reserved

-

Read: undefined. Write: should be zero.

[07:02]

ABF

6’h0

Number of additional beginning flags.

This 6 bit field indicates the number of additional
beginning flags, according to the encoding:

– 6‘b000000 = No additional beginning flags.

– 6‘b000001 = 1.

… = …

– 6‘b110000 = 48.

Any other value = Reserved.

[01:00]

MODE

2’h0

Infrared mode.

This 2 bit field allows to select the used infrared
mode, according to the encoding:

– 2‘b00 = SIR

– 2‘b01 = MIR

– 2‘b10 = FIR

– 2’b11 = Reserved

«
...
579
580
581
582
583
...
»

Summary of Contents for SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPEAr300

Brand: J4C Pages: 4

Brand: DayTronic Pages: 22

Brand: Radware Pages: 98

Brand: YOKOGAWA Pages: 150

Brand: ZKTeco Pages: 11

NOVASTAT EL DIGITAL

Brand: Taconova Pages: 7

Brand: Netafim Pages: 4

Brand: TREND Pages: 12

Brand: National Instruments Pages: 26

BLEUBOX R-IN-UHF-5239U

Brand: iDTRONIC Pages: 13

SUNSAVER SS-10-12V

Brand: Morningstar Pages: 26

Brand: NovaStar Pages: 11

Brand: Kelly Pages: 35

Brand: NELSEN WATER Pages: 16

Brand: Botex Pages: 36

Brand: S2Tech Pages: 4

Brand: Trio Pages: 8

Botex DMX RDM Tester

Brand: thomann Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands