STMicroelectronics SPEAr300 Reference Manual Download Page 550 | Manualshive

Page: 550 / 844

background image

HS_Media independent interface (MII)

RM0082

Doc ID 018672 Rev 1

24.8.3 MMC

transmit

interrupt register

The MMC transmit interrupt register maintains the interrupts generated when transmit
statistic counters reach half their maximum values. (MSB of the counters is set.) It is a 32 bit
wide register. An interrupt bit is cleared when the respective MMC counter that caused the
interrupt is read. The least significant byte-lane (bits[7:0]) of the respective counter must be
read in order to clear the interrupt bit.

[10]

-

1’h0

-

The bit is set when the rxoversize_g counter
reaches half the maximum value.

[09]

-

1’h0

-

The bit is set when the rxundersize_g counter
reaches half the maximum value.

[08]

-

1’h0

-

The bit is set when the rxjabbererror counter
reaches half the maximum value.

[07]

-

1’h0

-

The bit is set when the rxrunterror counter reaches
half the maximum value.

[06]

-

1’h0

-

The bit is set when the rxalignmenterror counter
reaches half the maximum value.

[05]

-

1’h0

-

The bit is set when the rxcrcerror counter reaches
half the maximum value.

[04]

-

1’h0

-

The bit is set when the rxmulticastframes_g counter
reaches half the maximum value.

[03]

-

1’h0

-

The bit is set when the rxbroadcastframes_g
counter reaches half the maximum value.

[02]

-

1’h0

-

The bit is set when the rxoctectcount_g counter
reaches half the maximum value.

[01]

-

1’h0

-

The bit is set when the rxoctectcount_gb counter
reaches half the maximum value.

[00]

-

1’h0

-

The bit is set when the rxframecount_gb counter
reaches half the maximum value.

Table 464.

MMC receive interrupt register bit assignments (continued)

Bit

Name

Reset value Type

Description

Table 465.

MMC transmit interrupt register bit assignments

Bit

Name

Reset value

Type

Description

[31:25]

Reserved -

RO

-

[24]

-

1’h0

-

The bit is set when the txvlanframes_g counter reaches
half the maximum value.

[23]

-

1’h0

-

The bit is set when the txpauseframes error counter
reaches half the maximum value.

[22]

-

1’h0

-

The bit is set when the txoexcessdef counter reaches
half the maximum value.

[21]

-

1’h0

-

The bit is set when the txframecount_g counter reaches
half the maximum value.

«
...
548
549
550
551
552
...
»

Summary of Contents for SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPEAr300

Brand: Wavetec Pages: 17

Brand: Calsense Pages: 9

Smart Controller

Brand: MaestroHome Pages: 10

GRAVIMETRIC AUGER FEEDER MGF-ST

Brand: Maguire Products Pages: 47

Brand: Magtrol Pages: 160

PowerFlex 755 IP00

Brand: Allen-Bradley Pages: 78

Pulsafeeder MPC Vector

Brand: Idex Pages: 114

CURTIS DC Series

Brand: NOCO Genius Pages: 2

Brand: Xylem Pages: 2

Brand: Samcen Pages: 65

Brand: zeeltronic Pages: 13

Brand: QD Dynamics Pages: 64

Brand: ZKTeco Pages: 27

TITAN CONTROLS KRONUS 2

Brand: Sunlight Supply Pages: 4

Brand: Srne Pages: 13

Series RHCN-7000

Brand: Omega Engineering Pages: 2

Brand: WAM Pages: 2

Brand: Zamel Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands