STMicroelectronics SPEAr300 Reference Manual Download Page 532 | Manualshive

Page: 532 / 844

background image

HS_Media independent interface (MII)

RM0082

Doc ID 018672 Rev 1

Note:

This bit is not used (reserved) when the Receive FIFO size is less than 4Kbytes.

●

FEF

Setting this bit, all frames except runt-error frames will be forwarded to the DMA.
Otherwise, the Receive FIFO will drop frames with error status.

●

FUF

Setting this bit, the Receive FIFO will forward undersized frames (frames with no error
and length less than 64 bytes, including pad-bytes and CRC). Otherwise, the Receive
FIFO will drop all frames of size less than 64 bytes, unless frame is already transferred
due to lower value of RTC value (in this register).

●

RTC

This 2 bit field allows start of transfer request to DMA when the frame size in the
Receive FIFO is larger than the stated threshold, according to encoding below:

●

OSF

Setting this bit, the DMA is instructed to process a second frame of the Transmit List
even before to obtain the status of the first frame.

●

SR

Setting this bit, the receive process is placed in the Running state, and the DMA
attempts to acquire the descriptor from the Receive List and process incoming frames.
Descriptor acquisition is attempted from the current position (pointed by the Receive
Descriptor List Address register) or at position retained in case of reception was
previously stopped.

Clearing this bit, the receive process is placed in the Stopped state after completing the
transmission of the current frame.

24.7.10 Interrupt

enable

register (Register7, DMA)

The Interrupt Enable is a register which enables the interrupts reported by register5
(

Section 24.7.8

). The Interrupt Enable Bit assignments are given in

Note:

Setting a bit enables the corresponding interrupt. After reset, all interrupts are disabled.

Table 440.

RTC field bit assignments

Value

Threshold (Byte)

2‘b00

64

2‘b01

32

2‘b10

96

2‘011

128

Table 441.

Interrupt enable register bit assignments

Bit

Name

Reset value

Type

Description

[31:17]

Reserved

-

RO

Read: undefined.

[16]

NIE

1’h0

RW

Normal interrupt summary enable.

[15]

AIE

1’h0

RW

Abnormal interrupt summary enable.

[14]

ERE

1’h0

RW

Early receive interrupt enable.

«
...
530
531
532
533
534
...
»

Summary of Contents for SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPEAr300

Brand: Acclaim Lighting Pages: 32

Brand: M-system Pages: 103

Brand: M-system Pages: 18

Brand: Parker Pages: 32

Brand: Rayrun Pages: 4

Brand: Centurion Pages: 16

Brand: Nice Pages: 32

Brand: Samcen Pages: 65

Brand: Barco Pages: 4

Brand: Zero 88 Pages: 34

Brand: DAPAudio Pages: 11

Brand: Akytec Pages: 15

Brand: Siro Pages: 2

Brand: Fisher Pages: 44

PROFOX PF-M100X

Brand: AUMA Pages: 56

Brand: SUNWIND Pages: 53

Brand: GAC Pages: 22

Brand: Cablematic Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands