STMicroelectronics SPEAr300 Reference Manual Download Page 268 | Manualshive

Page: 268 / 844

background image

Miscellaneous registers (Misc)

RM0082

Doc ID 018672 Rev 1

12.5.2 Miscellaneous

register

global space address map

Next table shows the miscellaneous global register map.

12.5.3 RAS1/2_GPP_INP

register

The RAS1/2_GPP_INP is a group of RO general purpose input registers used to pass
different kind of information from the reconfigurable logic array toward the internal core logic.
The register bit assignments is detailed in the next two tables.

Table 202.

Miscellaneous global space registers overview

Miscellaneous Global Space Register Map

Base Address: 0xFCA8.0000

Register Name

Alias-1 Offset

0x0.8000

Alias-2 Offset

0x1.8000

Type

Register Displacement (single region)

RAS_GPP1_IN

0x00

R/W

RAS_GPP2_IN

0x04

R/W

RAS_GPP1_OUT

0x08

R/W

RAS_GPP2_OUT

0x0C

R/W

RAS_GPP_EXT_IN

0x10

R/W

RAS_GPP_EXT_OUT

0x14

R/W

Reserved

0x18

R/W

Reserved

0x1C

R/W

Table 203.

RAS_GPP1_IN register bit assignments

RAS_GPP1_IN Register

0x000

Bit

Name

Reset
Value

Description

[31:00]

gpp1_in[31:00]

-

General purpose input register (RO) which return the
current value of the programmable logic GPP_INP
(31:00) signals.

Table 204.

RAS_GPP2_IN register bit assignments

RAS_GPP2_IN Register

0x004

Bit

Name

Reset
Value

Description

[31:00]

gpp2_in[31:00]

-

General purpose input register (RO) which return the
current value of the programmable logic GPP_INP
(63:32) signals.

«
...
266
267
268
269
270
...
»

Summary of Contents for SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPEAr300

Brand: iCeeO2 Pages: 7

Brand: TCS Basys Controls Pages: 2

coviva Smartbox TKP100A

Brand: hager Pages: 45

Brand: YASKAWA Pages: 49

Brand: M-system Pages: 17

Brand: ZKTeco Pages: 2

Brand: Voltech Pages: 8

Brand: Pangolin Pages: 35

ECL Comfort 300

Brand: Danfoss Pages: 75

Brand: maxon motor Pages: 44

Brand: Current Pages: 4

Brand: PEAS Pages: 4

Brand: Sollae Systems Pages: 72

CYPRESS Traveo S6J335 Series

Brand: Infineon Technologies Pages: 308

Brand: Niko Pages: 80

Brand: Fairchild Pages: 4

HYGRASREG KH-10

Brand: S+S Regeltechnik Pages: 16

Brand: Harsen Pages: 55

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands