manualshive.com logo in svg

STMicroelectronics RM0365, Reference Manual

The STMicroelectronics RM0365 Reference Manual is the comprehensive guide for successfully operating and maximizing the potential of your device. This invaluable resource is available for free download at manualshive.com, ensuring easy access to detailed instructions and information necessary for efficient product utilization.

Share
Download
background image

DocID025202 Rev 7

514/1080

RM0365

Advanced-control timers (TIM1)

549

This is done in the following steps:
1.

Configure the corresponding DMA channel as follows: 
–

DMA channel peripheral address is the DMAR register address 

–

DMA channel memory address is the address of the buffer in the RAM containing 
the data to be transferred by DMA into CCRx registers. 

–

Number of data to transfer = 3 (See note below). 

–

Circular mode disabled. 

2.  Configure the DCR register by configuring the DBA and DBL bit fields as follows: 

DBL = 3 transfers, DBA = 0xE. 

3.  Enable the TIMx update DMA request (set the UDE bit in the DIER register). 
4. Enable 

TIMx 

5.  Enable the DMA channel

This example is for the case where every CCRx register to be updated once. If every CCRx 
register is to be updated twice for example, the number of data to transfer should be 6. Let's 
take the example of a buffer in the RAM containing data1, data2, data3, data4, data5 and 
data6. The data is transferred to the CCRx registers as follows: on the first update DMA 
request, data1 is transferred to CCR2, data2 is transferred to CCR3, data3 is transferred to 
CCR4 and on the second update DMA request, data4 is transferred to CCR2, data5 is 
transferred to CCR3 and data6 is transferred to CCR4.

Note:

A null value can be written to the reserved registers.

20.3.28 Debug 

mode

When the microcontroller enters debug mode (Cortex-M4

®

F core halted), the TIMx counter 

either continues to work normally or stops, depending on DBG_TIMx_STOP configuration 
bit in DBG module.

For safety purposes, when the counter is stopped (DBG_TIMx_STOP = 1), the outputs are 
disabled (as if the MOE bit was reset). The outputs can either be forced to an inactive state 
(OSSI bit = 1), or have their control taken over by the GPIO controller (OSSI bit = 0), 
typically to force a Hi-Z.

For more details, refer to 

Section 33.14.2: Debug support for timers, watchdog, bxCAN and 

I2C

.

For safety purposes, when the counter is stopped (DBG_TIMx_STOP = 1), the outputs are 
disabled (as if the MOE bit was reset). The outputs can either be forced to an inactive state 
(OSSI bit = 1), or have their control taken over by the GPIO controller (OSSI bit = 0) to force 
them to Hi-Z. 

Summary of Contents for RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RM0365

Dave Embedded Systems ARM Cortex-A9 MPCore Quick Start Manual preview
ARM Cortex-A9 MPCore
Brand: Dave Embedded Systems Pages: 67
Commell LS-570 User Manual preview
LS-570
Brand: Commell Pages: 58
EKF Electronik CompactPCI CC8-BLUES User Manual preview
CompactPCI CC8-BLUES
Brand: EKF Electronik Pages: 52
ESD ECS-CPCIs/FPGA Hardware Manual preview
ECS-CPCIs/FPGA
Brand: ESD Pages: 28
S&T kontron COMe-cEL6 User Manual preview
kontron COMe-cEL6
Brand: S&T Pages: 99
Cypress Semiconductor CY7C1329H Specification Sheet preview
CY7C1329H
Brand: Cypress Semiconductor Pages: 16
ZALMAN ZM-MFC1 Combo User Manual preview
ZM-MFC1 Combo
Brand: ZALMAN Pages: 7
Intel BLKDP45SG - MB 1333FSB DDR3 1333 Aud+Lan RAID SATA ATX Product Manual preview
BLKDP45SG - MB 1333FSB DDR3 1333 Aud+Lan RAID SATA ATX
Brand: Intel Pages: 86
Lanner FW-7551 User Manual preview
FW-7551
Brand: Lanner Pages: 38
Dataprobe iBoot Instruction Manual preview
iBoot
Brand: Dataprobe Pages: 16
Quadram Quadboard Operation Manual preview
Quadboard
Brand: Quadram Pages: 21
Radica Games DAVID-II 716 Operating And Maintenance Instruction Manual preview
DAVID-II 716
Brand: Radica Games Pages: 40
Airvana ipBTS C30 Installation And Commissioning Manual preview
ipBTS C30
Brand: Airvana Pages: 90
Renesas HD74HCT1G04 Datasheet preview
HD74HCT1G04
Brand: Renesas Pages: 8
IBA FOB-SDexp Manual preview
FOB-SDexp
Brand: IBA Pages: 36
ADTRAN 1200127L1 User Manual preview
1200127L1
Brand: ADTRAN Pages: 20
Boser HS-2605 Manual preview
HS-2605
Brand: Boser Pages: 82
IBM 32R1860 - Nortel Layer 2/3 Copper GbE Switch... User Manual preview
32R1860 - Nortel Layer 2/3 Copper GbE Switch...
Brand: IBM Pages: 14

Brands by name

Popular brands

Load more brands