manualshive.com logo in svg

STMicroelectronics RM0365, Reference Manual

The STMicroelectronics RM0365 Reference Manual is the comprehensive guide for successfully operating and maximizing the potential of your device. This invaluable resource is available for free download at manualshive.com, ensuring easy access to detailed instructions and information necessary for efficient product utilization.

Share
Download
background image

DocID025202 Rev 7

114/1080

RM0365

Reset and clock control (RCC)

154

Figure 11. Simplified diagram of the reset circuit

Software reset

The SYSRESETREQ bit in Cortex-M4

®

F Application Interrupt and Reset Control Register 

must be set to force a software reset on the device. Refer to the STM32F3xx/F4xx Cortex

®

-

M4 programming manual (PM0214)

 

for more details. 

Low-power management reset

There are two ways to generate a low-power management reset:
1.

Reset generated when entering Standby mode: 
This type of reset is enabled by resetting nRST_STDBY bit in User Option Bytes. In this 
case, whenever a Standby mode entry sequence is successfully executed, the device 
is reset instead of entering Standby mode. 

2.  Reset when entering Stop mode: 

This type of reset is enabled by resetting nRST_STOP bit in User Option Bytes. In this 
case, whenever a Stop mode entry sequence is successfully executed, the device is 
reset instead of entering Stop mode. 

For further information on the User Option Bytes, refer to 

Section 4: Option bytes

.

Option byte loader reset

The option byte loader reset is generated when the OBL_LAUNCH bit (bit 13) is set in the 
FLASH_CR register. This bit is used to launch the option byte loading by software.

9.1.3 RTC 

domain 

reset

The RTC domain has two specific resets that affect only the RTC domain (

Figure 8 on 

page 97

).

An RTC domain reset only affects the LSE oscillator, the RTC, the Backup registers and the 
RCC 

RTC domain control register (RCC_BDCR)

. It is generated when one of the following 

events occurs.
1.

Software reset, triggered by setting the BDRST bit in the 

RTC domain control register 

(RCC_BDCR)

.

2. V

DD

 power-up if V

BAT

 has been disconnected when it was low.

5

38

9

''

069

6\VWHPUHVHW

([WHUQDO

UHVHW

1567

)LOWHU

3XOVH

JHQHUDWRU

PLQ—V

::'*UHVHW
,:'*UHVHW
3RZHUUHVHW
6RIWZDUHUHVHW
/RZSRZHUPDQDJHPHQWUHVHW
2SWLRQE\WHORDGHUUHVHW
([LWIURP6WDQGE\PRGH

Summary of Contents for RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RM0365

Magma PE6R4-I Quick Installation Manual preview
PE6R4-I
Brand: Magma Pages: 2
SIIG ID-P20211-S1 Quick Installation Manual preview
ID-P20211-S1
Brand: SIIG Pages: 20
Tandy 26-3814 Operation Manual preview
26-3814
Brand: Tandy Pages: 24
Comtrend Corporation WAP-5922MP Quick Install Manual preview
WAP-5922MP
Brand: Comtrend Corporation Pages: 4
Bridgeworks Tamar FCSAS102800 User Manual preview
Tamar FCSAS102800
Brand: Bridgeworks Pages: 56
UNICORECOMM UM620N User Manual preview
UM620N
Brand: UNICORECOMM Pages: 19
IEI Technology WSB-H610-R11 User Manual preview
WSB-H610-R11
Brand: IEI Technology Pages: 146
IBM TSO/E REXX User Manual preview
TSO/E REXX
Brand: IBM Pages: 242
Moxa Technologies CP-102N-T Quick Installation Manual preview
CP-102N-T
Brand: Moxa Technologies Pages: 8
Variscite VAR-SOM-MX6 HEAT PLATE KIT Quick Start Manual preview
VAR-SOM-MX6 HEAT PLATE KIT
Brand: Variscite Pages: 3
IBM 25CPC710 Application Note preview
25CPC710
Brand: IBM Pages: 8
iTON ID6ZFN-BK0 User Manual preview
ID6ZFN-BK0
Brand: iTON Pages: 12
Zoltrix Audio Plus 3200 Hardware Manual preview
Audio Plus 3200
Brand: Zoltrix Pages: 34
National Instruments DAQ X NI 634 Series User Manual preview
DAQ X NI 634 Series
Brand: National Instruments Pages: 278
ADTRAN NetVanta 3430 Manual preview
NetVanta 3430
Brand: ADTRAN Pages: 2
ADTRAN OC-12 Manual preview
OC-12
Brand: ADTRAN Pages: 2
ADTRAN SFP Series Quick Start preview
SFP Series
Brand: ADTRAN Pages: 4
ADTRAN TRACER 4205 Quick Start Manual preview
TRACER 4205
Brand: ADTRAN Pages: 9

Brands by name

Popular brands

Load more brands