25
USB AUDIO
1. INTERFACE
The VX-2043FDR/VX-1443FDR is equipped with a stereo
bi-directional USB 1.1 compliant audio CODEC. It is fully
compliant with USB 2 ports and standard Windows and
MAC Core Audio Drivers.
2. Connecting
VX-2043FDR/VX-1443FDR have USB B TYPE jack. You
can use USB lead type A to B of computer. Plug it in and
your computer will find it and be able to transfer audio to and
from the VX-2043FDR/VX-1443FDR USB device.
3. D.A.W Software
You will need some form of audio software running on your
computer to be able to store and play back what you record,
but ona basic level, you can use your computers media player
to play straight to the Device.
4. Computer Play Signal Level
If the seems to be no audio transfer between the computer
and your device, or level is very low, please check the volume
level setting of Audio device in your computer's operating
system. This may need to be set to the Max position.
USB 오디오
1. 인터페이스
VX-2043FDR/VX-1443FDR 믹서는 양방향성 USB 1.1에 대응하
는 오디오 코덱이 장착되어 있습니다.
USB 2 포트들에 완벽하게 대응하며 정품 윈도우와 맥 코어 오디
오 드라이버와 호환됩니다.
2. 연결
VX-2043FDR/VX-1443FDR 믹서는 USB B TYPE 잭을 가지고 있
습니다. USB 리드 타입 A 에서 B로 컴퓨터와 연결할 수 있습니다.
컴퓨터와 믹서를 연결하면 컴퓨터는 VX-2043FDR/VX-1443FDR
USB로 오디오 신호를 전송할 수 있도록 설정할 것입니다.
3. D.A.W 소프트웨어
녹음하려는 것을 컴퓨터에 저장하거나 플레이 백하기 위해서는
오디오 소프트웨어가 필요합니다. 하지만 간단하게 컴퓨터 자체의
미디어 플레이어로도 가능합니다.
4. 컴퓨터 플레이 신호 레벨
만약 당신의 컴퓨터와 기기 간에 오디오 신호의 이동이 일어나지
않는 것처럼 보인다면 신호 레벨이 너무 낮아서일 수 있습니다.
컴퓨터 운영 시스템에서의 오디오 기기의 볼륨을 다시 체크해 보
시고 이 경우 볼륨을 최대로 올리셔야 합니다.
<
USB CONNECTION
l USB 연결>
컨트롤 패널 / 사운드&오디오 기기 /볼륨
CONTROL PANEL/Sound&Audio Device/Volume
스텝 1.
볼륨 레벨 체크
스텝 2.
마우스로 볼륨 레벨을 최대로 끌어 놓으시고“Apply”를
클릭해 주세요.
만약 SOUND FORGE, CAKEWORK 등의 다른 레코딩 소프트 웨
어를 사용하고자 하신다면 따로 소프트를 준비하셔야 합니다.
그런 소프트 웨어를“DIGITAL AUDIO WORK STATION
(DAW)”라고 부릅니다.
STEP 1.
Volume level check
STEP 2.
If the volume level is not full up, then drag it fully
up and click "Apply"
If you want use recording to computer there are some
different recording software audio drivers like a SOUND
FORGE, CAKEWORK. We called “DIGITAL AUDIO
WORK STATION(DAW)”
<
STEP 1
>
<
STEP 2
>
Ⅰ
Introduction
l
제품 소개
4.
Panel Descriptions
l
각 부의 명칭
24
1. SUB Group Output Jack
Provides the group outputs on 1/4" jacks at line level. Suitable
for connection to unbalanced devices. These jacks are usually
patched to the inputs of a multi track deck, or to secondary
amplifiers in a complex installation.
2. Mono Main
The Mono Main output is a sum of the left and right mix
buses, buffered with its own electronically balanced output
amplifiers. Like the right main mix and left main mix, the
Mono Master output appears on a male XLR type connector
near the center of the rear panel.
3. Subwoofer switch
The VX mixer has an integrated mono summing 75Hz 3rd-
order Low Pass Filter. Activated Low pass Filter when the
switch ON for Mono Main output.
4. Main Outputs: XLR Jacks
These are male XLR-type connectors, designed to mate with
a standard mic cable. The Right and Left main outputs are
electronically balanced, with Pin1 connected to ground, Pin2
to signal "Hot"(or "High" or "+") and Pin3 to signal "Cold"(or
"Low" or "-"). With the master fader at untie, nominal output
level is +4dBu.
5. Main Outputs: 1/4" Jacks
These jacks carry the same signals as the Right and Left main
mix connectors. Main outputs L and R are impedance balanced
¼″TRS(tip-ring-sleeve) phone jacks with ground wired to
sleeve, signal "hot"(or "high" or "+") to the tip and signal
"cold"(or "low" or "-") wired to the ring. You can connect
either balanced or unbalanced inputs to these outputs nominal
level is 0dBu.
6. Main Insert L&R
These 1/4" TRS jacks are for connecting serial effects such as
compressors, equalizers, deessers, of filters. The insert point
is after the mix amps, but before the MAIN MIX fader. Refer
to the description of the channel insert on the previous page
to see how to make this connection. The insert jacks require
4.
Panel Descriptions
l
각 부의 명칭
REAR PANEL SECTION /
후면부
1
8
7
2
3
9
4
5
6
10
the use a special "Y" cable with a Tip/Ring/Sleeve plug on the
mixer end.
7. Phantom Power Switch
Enables the 48V Phantom Power system for use with
condenser microphones requiring an external power source.
Most professional condenser micro phones require phantom
power, which is a +48Vdc delivered to the microphone on
pins 2 and 3 of the XLR the microphone connector. Turn on
the +48V switch if your microphone needs phantom power.
An LED lights indicate that phantom power is active on
the front. Dynamic microphones do not required phantom
power. However, phantom power will not harm most dynamic
microphones should you accidentally plug one in while the
phantom power is turned on. Be careful with older ribbon
microphones. Check the manual for your microphone to find
out for sure whether or not phantom power can damage it.
Note
: Be sure the related all output channel fader is turned
down when connecting microphones to the MIC Inputs,
especially when phantom power is turned on, to prevent pops
from getting through to the speakers.
8. Power Switch
With this switch on, and adequate AC power Dapplied, the
power indicator(17) should light. If it does not, turn the power
off and re-check the power connection before proceeding.
9. AC Input/Fuse Holder
Standard IEC-type power cord connection with integral mains
fuse holder, equipped with 1A 250V fast-blow fuse for AC
input 120V; Other country are 500mA, 250V Time-Lag fuse
for AC input 220-240V.
WARNING
: Replace fuse ONLY with same-type fuse as
listed. Failure to do so can result in fire or electrical shock
hazard.
10. Channel Direct Output
This provides an ideal source for external processing unit,
or directly sent to the tape machine or hard disk recorder for
multi-track recording.(VX-1443FDR only)
(VX-1443FDR ONLY)
