STK Professional Audio VX series, Owner'S Manual, Page: 12 / 32

12
4. Panel Descriptions
l
각 부의 명칭
B. Stereo Input Channel
16. MIC input
(VX-1204FX CH5/6-7/8, VX-1604FX CH9/10-11/12)
This is where you connect your any microphones and
Phantom powering (+48V) is available for these inputs.
Standard XLR 3 pin female connector.
Note : If you are using unbalanced microphones, do not use
+48V.
17. Left (Mono) Input
Accepts 1/4" TS (tip/sleeve) unbalanced sources at line level.
1/4" connector tip is "Hot(+)", and sleeve is "Shield(GND)".
Input is routed to the left output bus. In the absence of a plug
in the right input (18), the left input signal is also provided
to the right input, so that the channel functions as a mono
channel.
18. Right Input
Similar to the left input, but any inputs to this connector are
only routed to the right output bus.
19. 20dB Pad Switch
This switch controls the 20dB input attenuator for the Mic/
Line input.
20. High Equalization
This control gives you up to 15 dB boost or cut at 12kHz,
and it is also flat at the center detent. Use it to add sizzle to
cymbals, and an overall sense of transparency or edge to the
keyboards, vocals, guitar, and bacon frying. Turn it down a
little to reduce sibilance, or to hide tape hiss. Affects both left
and right channel input signals.
21. MID EQUALIZATION
Provides ±12dB of peak/dip equalization control to boost
or cut midrange signals centered at 2.5kHz. Affects both
left and right channel input signals. Midrange EQ is often
thought of as the most dynamic because the Frequencies that
define any frequencies particular sound are almost always
found in this range. You can create many interesting and
useful EQ changes by turning this knob down as well as up.
22. Low Equalization (nearly identical to mono CH Low
EQ)
Provides ±15dB of shelving equalization control to boost or
cut low frequency signals 80Hz and below. Affects both left
and right channel input signals.
23. AUX1/MON Send
This control knobs tap a portion of each channels signal out
to either an effects processor or for stage monitoring. Adjusts
the amount of mono-summed channel input signal supplied
to the AUX 1/Monitor output. AUX1/Monitor send is post
EQ, pre fader feed.
24. Aux2 / EFX Send
This control knobs tap a portion of each channels signal out
to either an effects processor or for stage monitoring. Adjusts
2 TRACK
IN
2 TRACK
OUT
1=GND
3=COLD(-)
2=HOT(+)
1=GND
3=COLD(-)
2=HOT(+)
UNBAL UNBAL
UNBAL
UNBAL
Digital Effect Program
01 Reverb Hall 2 5.0 sec
02 Reverb Hall 2 3.0 sec
03 Reverb Room 2.0 sec
04 Reverb Room 1.0 sec
05 Reverb Plate 3.5 sec
06 Reverb Plate 1.5 sec
07 Delay & Reverb 170ms/3 sec.
08 Delay & Reverb 300ms/5 sec. 09 Delay 50% F.B. 100ms
10 Delay 50% F.B. 200ms
11 Delay 50% F.B. 350ms
12 Delay 50% F.B. 500ms
13 Chorus & Reverb slow/4.0 sec.
14 Chorus & Reverb med/2.0 sec.
15 Flanger & Reverb slow/4.0 sec.
16 Flanger & Reverb med/2.0 sec.
UNBAL=
GND TIP(+)
GND TIP(+)
RING(-)
BAL=
U
10 0
U
10 0
U
10 0
U
10 0
U
10 0
U
10 0
U
10 0
U
10 0
+10
+7
+4
-4
-10
-20
-30
-40
U
-15
(0dBU)
+10
+7
+4
-4
-10
-20
-30
-40
U
-15
(0dBU)
+10
+7
+4
-4
-10
-20
-30
-40
U
-15
(0dBU)
+10
+7
+4
-4
-10
-20
-30
-40
U
-15
(0dBU)
Solo Mode
+10
+7
-4
-10
-20
-30
-40
-15
(+4dBU)
U
U
(0dBU)
+10
+7
-4
-10
-20
-30
-40
-15
(+4dBU)
U
U
(0dBU)
+10
+7
-4
-10
-20
-30
-40
-15
(+4dBU)
U
U
(0dBU)
+10
+7
-4
-10
-20
-30
-40
-15
(+4dBU)
U
U
(0dBU)
U
-18dBU 0
U
-19dBU 0
★ ★
★
★
13 -14 15 -16
UNBAL=
GND TIP(+)
1=GND
3=COLD(-)
2=HOT(+)
1=GND
3=COLD(-)
2=HOT(+)
U
10 0
U
10 0
U
10 0
U
10 0
+10
+7
+4
-4
-10
-20
-30
-40
U
-15
(0dBU)
+10
+7
+4
-4
-10
-20
-30
-40
U
-15
(0dBU)
-58 -10
-33dB +14dB
-10
U
-20
U
M
ic
G
ain
Lin
e
Tr
im
-58 -10
-33dB +14dB
-10
U
-20
U
M
ic
G
ain
Lin
e
Tr
im
SLEEVE TIP(+)
RING(-)
SLEEVE TIP(+)
RING(-)
25
24
23
22
21
20
18
17
16
19
26
27
28
29
FRONT PANEL /
정면부
B. Stereo Input Channel /
스테레오 입력 채널