background image

Warranty Information

UNPACKING

As a part of our system of quality

control, every

STK product is carefully

inspected before leaving the factory to

insure flawless appearance. After unpacking,

please inspect for any physical damage.

Save the shipping carton and all packing

materials, as they were carefully designed

to reduce the possibility of transportation

damage should the unit again require

packing and shipping. In the event that

damage has occurred,

immediately notify your dealer so that

a written claim to cover the damage

can be initiated with the carrier.

The right to any claim against a

public carrier can be forfeited if the

carrier is not promptly notified and if

the shipping carton and packing

materials are not available for

inspection by the carrier. Save all

packing materials until the claim has

been settled.

STK LIMITED 5 YEAR WARRANTY

STK electronics are warranted to

be free from defects in materials and

workmanship under normal use for a

period of 5 years from date of original

purchase. During that period. STK will

at its option, repair or replace materials

at no charge if product has been

delivered to STK by an

STK dealer or STK Service Center

together with the original sales receipt

or other proof of purchase. Warranty

excludes fuses, exterior finish, normal

wear, failure due to abuse, or operation

outside of specified ratings. Warranty

applies to original purchaser only.

This warranty gives you specific legal

rights which vary from state to state.

For more information about warranty

repair, please contact: Customer

Service Dept., The STK Co.

FOR YOUR RECORDS

All of us at STK thank you for

your expression of confidence in STK

products. The unit you have purchased

is protected by a limited 5 year

warranty. To establish the warranty, be

sure to fill out and mail the warranty

card attached to your product.

For you own protection, fill out the information below for you own records.

Model Number

Serial Number

Dealer

Date Of Purchase

Salesman

Phone

Other Information

Summary of Contents for VM 10SD Stereo























Reviews: