14
Shot of steam
Shot of steam can be activated after pressing the steam trigger twice continuously. An interval of at least 15
seconds must be maintained between two continuous cycles. The “Shot of steam” function can be only
activated under ECO and Ηigh steam rate.
Cord winding groove
When not in use, the steam supply hose can be wound along the cord winding groove for storage and the
power cord can be tied well with a cable tie. Follow the operation in the section of
“CLEANING AND
MAINTENANCE”
.
Automatic power off
If there is no steam sprayed out of the soleplate, the appliance will turn off automatically if no operation
within 10 minutes. To restart the appliance, just need to press the power button again.
Correct placement of iron on the thermal insulation stand
When the iron is put on the thermal insulation stand, it must be placed on it correctly.
Vertical steam
With vertical steam function for removing wrinkles from hanging garments, curtains, drapes, and more.
BEFORE FIRST USE
1.
Remove any sticker or protective foil from the soleplate.
2. Heat up the iron at the maximum temperature and iron over a piece of damp cloth for several minutes
for the purpose of removing any residue on the soleplate according to the section of
“Steam ironing”
.
NOTE:
It is normal that strange odor comes out from the unit for the first use. This will cease after a
short while.
NOTE:
Some particles may come out of the soleplate when you use the iron for the first time. This is
normal; the particles are harmless and stop coming out of the iron after a short while.
NOTE:
After you switch on the appliance, the water pump in the unit base may produce a sound when
spraying steam.
NOTE:
During the heating process of the soleplate, there will be little water coming out from the
soleplate automatically and this phenomenon will continue for about 3 seconds, This is normal.
USING YOUR STEAM STATION IRON
The appliance has two ironing ways. You can use dry ironing or steam ironing, the details refer to the
following:
Dry ironing
1.
Put the iron on the thermal insulation stand of unit base.
2. Connect the plug to wall outlet and press down the Power switch, the power indicator turns on.
3. Turn the temperature dial to your desired setting, which is depended on the fabric of garment, and the
temperature indicator will illuminate. The iron starts heating. Refer to
“IRONING TIPS”
and
“ADDITIONAL
TABLE”
as below when select temperature.
Summary of Contents for SP2010
