background image

www.stingerworld.com 

CS58 Cap Stapler 

IMPORTANT   INFORMATION   

PERSONAL SAFETY ITEMS 
 

Do not use tool prior to reading the Owner

s Manual. 

Always wear eye protection that conforms to ANSI requirements (Z87.1) and 
provides protection against flying particles both from the front and side.  Eye 
protection should be worn by the operator and by others in the work area.  Eye 
protection is required to protect against flying fasteners and debris that could 
possibly cause severe eye injury. 

The employer is responsible to enforce the use of eye protection equipment by the tool 
operator and all other personnel in the work area. 

To prevent accidental injuries: 

Handle the tool with care 

Always assume that the tool contains fasteners 

Always disconnect the air hose from the 

STINGER CS58

 when: 

loading staples and/or caps 

performing inspection, maintenance or repair 

clearing a staple or collated cap jam 

the tool is not in use 

leaving the work area 

moving the 

STINGER CS58

 to another work location 

handing the 

STINGER CS58

 to another person 

storing the tool 

Never point the tool toward yourself or anyone else 

Never engage in horseplay 

Never hold or carry the tool with a finger on the trigger 

Never place a hand or any other part of the body in the fastener discharge area of 
the tool while the air supply is connected 

Summary of Contents for CS58

















Reviews: