manualshive.com logo in svg

Still FXV 14 N, Original Instructions Manual

Share
Download
Still FXV 14 N Original Instructions Manual Download Page 102

Charging the battery using an exter-

nal charger 

 CAUTION

Deep discharging may damage the battery.

–

Charge the battery immediately.

–

Park the truck safely.

–

Before charging, check the condition of the

battery cable and the charger cable. Re-

place them if necessary.

–

Open the hood and leave open.

–

Remove the battery handle connector (1)

from the truck plug (2).

–

Connect the battery connector to the wall-

mounted connector.

 WARNING

Electrical risk
Only unplug the battery connector from the battery

charger when both the battery charger and truck are

switched off.

 NOTE

Follow the instructions provided by the battery

and battery charger manufacturers (equalising

charge).

 WARNING

Risk of damage, short circuit or explosion.
Do not place any metallic objects or tools on the bat-

tery.
Smoking is prohibited.

 WARNING

The electrolyte (diluted sulphuric acid) is toxic and

very caustic.
Follow the safety regulations when handling battery

acid.

Use

4

Handling the battery

 92

11748011551 EN - 02/2021  -  09

Summary of Contents for FXV 14 N

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands