Still EXD 18 Original Instructions Manual Download Page 122

Page: 122 / 146

Checking the condition of cables,

terminals and battery connector

–

Check that the cable insulation is undam-

aged and that there are no signs of over-

heating at the connections.

–

Check that the "+" and "-" output terminals

are not sulphated (presence of white salt).

–

Check the condition of the battery connec-

tor contacts and the presence of the keying

pin.

–

If the truck is equipped with an on-board

charger, check the condition of the spindles

of the mains socket. No oxidation must be

present and the wires must not be dam-

aged.

CAUTION

The points mentioned above can cause serious inci-

dents. In case of an incident, contact our service en-

gineers as quickly as possible.

Servicing the pump motor

Checking the electrical connections

–

Check the mounting, condition and insula-

tion of the pump motor cables (1).

–

Eliminate any traces of oxidation.

–

Replace faulty cables.

NOTE

Oxidised connections and faulty cables will re-

sult in a drop in voltage, leading to malfunc-

tions.



Maintenance

Electrical equipment

112

1160 801 15 51 EN - 02/2021 - 11

Summary of Contents for EXD 18



















































































































































Search results

Summary of Contents for EXD 18

Reviews:

Related manuals for EXD 18

Brands by name

Popular brands

Still EXD 18, Original Instructions Manual

Search results

Summary of Contents for EXD 18

Reviews:

Related manuals for EXD 18

Brands by name

Popular brands