Still CX-M 10 Operating Instructions Manual Download Page 64

Page: 64 / 152

Operation

Driving

1044_501-006

1044_501-007

1044_501-008

Driving, pedestrian operation with

push button

NOTE

The fork lift truck is fitted with push buttons

(1) and (2) on both sides of the seat backrest,

enabling the truck to be driven in pedestrian

mode from either side. The speed is reduced;

the tiller (3) can be used at any time to steer so

that the truck keeps going forward in a straight

line.

CAUTION

Take care when operating, especially if the user is

not familiar with using this function.

DANGER

Risk of crushing feet.
Do not use this function for turning.
This function is designed to maintain a straight line.
Proceed from the cockpit with very slight move-

ments.

NOTE

The lift truck must be switched on. If the push

button (4) or (5) are pushed in for quite a long

time, a safety circuit immobilises the truck. If

this occurs, simply release the push button

and then activate it again.

Forward travel via push button

– Press push-button (5). The truck moves

forwards; the speed is restricted to 4 km/h.

CAUTION

The speed cannot be adjusted. The driver must

walk alongside the fork lift truck.

– Release push button (5) to stop the truck.

The forklift truck will roll to a stop.

Reverse travel via push button

– Press the pressure switch (4). The lift truck

moves backwards; the speed is restricted

to 4 km/h.

4 499 284 [EN]

Summary of Contents for CX-M 10

























































































































































Search results

Summary of Contents for CX-M 10

Reviews:

Related manuals for CX-M 10

Brands by name

Popular brands

Still CX-M 10, Operating Instructions Manual

Search results

Summary of Contents for CX-M 10

Reviews:

Related manuals for CX-M 10

Brands by name

Popular brands