background image

6

3. [ASSEMBLE THE TURBO 500 CONDENSER]

Your water tubing is identified by a thick tube and a 

thin tube.
•  Connect the long, thick, clear tube to the block 

outlet 

C

. This will flow into your sink.

•  Connect the short thin, clear tube to make the top 

loop connection 

E

.

•  Connect the thin clear tube on the water inlet 

B

 , 

to your tap. This will flow from your tap (via the 

adaptor) into the condenser.

•  Connect the white tube on the spirit outlet 

D

.  

The distilled alcohol will flow from here to your  

collecting jug.

4.

 

[ADD THE THERMOMETER]

•  Place the battery in the thermometer.

•  A switch on the back allows you to turn the  

  thermometer on and off. A second switch allows you  

  to set the thermometer to Celsius or Fahrenheit.

•  Mount the thermometer in the mounting bracket   

  provided. Clip the panel onto the condenser near  

  the bottom.

•  Fit the stainless steel sensor probe into the hole 

A

.

•  Use a wire tie to tidy up any loose wiring.

5.   [BOILER]

Fit the Turbo 500 Condenser onto the Turbo 500 Boiler.

 

•  Check the Turbo 500 Condenser is full of saddles    

  inside. If the column is empty, you will need to  

  add copper saddles first, followed by the stainless   

  steel saddles packed in the column, then follow the  

  next step.  

Note: You may have a handful of saddles    
left, which cannot fit in the condenser, this   
is normal.

•  Holding the condenser upside down, unscrew the   

  nut at the base of the condenser; leave the black    

  O ring in the base of the column.

•  Place the Turbo 500 Boiler lid over the column and  

  screw the nut back in the column. Tighten firmly, 

  so that the lid doesn’t spin anymore. 

•  Place the lid and condenser on the Turbo 500 Boiler,  

  in position where you can see the thermometer.

•  Secure lid onto the Turbo 500 Boiler base with 

  the clips.

IMPORTANT: Ensure the Turbo 500 
Condenser is standing straight, or it will 
not operate properly during distillation.

Water outlet temperature sensor
Cooling water inlet
Water outlet 
Spirit outlet 
Top loop connections

cold  

water  

in

warm  

water  

out

spirit

YOU ARE NOW READY FOR DISTILLATION

C

A

A

B

C
D

E

B

D

water

E

Summary of Contents for TURBO 500

















Reviews: