q
Mowing Head with Automatic
Line Feed
Approved Combinations
The STIHL SuperCut 40-2 is approved for
use with the following STIHL brushcutters:
- FS 160, FS 180, FS 220, FS 260,
FS 280, FS 290, FS 300, FS 310,
FS 350, FS 360 (from 2010), FS 400,
FS 410 (from 2010), FS 450, FS 460,
FS 480, FS 490
The STIHL SuperCut 40-2
must not
used
on the following STIHL brushcutters:
- FS 260 RC, FS 360 up to 1997 (year of
manufacture), FS 410 C K,
FS 460 C-M K, FS 460 RC-M,
FS 490 C-M K
This mowing head is approved for use on
STIHL brushcutters only.
The STIHL SuperCut 40-2 is approved only
in combination with a properly mounted
deflector for mowing heads. The
deflector (
1
) must be equipped with a line
limiting blade (
2
).
Mounting Deflector for Mowing
Heads
• Mount the deflector as described in the
power tool's instruction manual. See
STIHL AutoCut or TrimCut mowing
heads.
2
681BB256 KN
1
2
1
Mounting the Mowing Head
• Use the guard ring for mowing
applications.
•
Do not
use the guard ring for sawing
applications.
• Mount the mowing head as described in
the power tool's instruction manual. See
STIHL AutoCut or TrimCut mowing
heads.
Adjusting Mowing Head to Suit
Brushcutter
Opening the mowing head
• Press in the two tabs on either side of
head and pull the cover off upwards.
Adjusting the mowing head
• Fitting the special wrench:
– Line up pointer in direction of scale.
– Engage lugs in recesses.
• Press wrench fully home – spring force
turns the wrench clockwise to 9 on the
scale – or it is already on 9.
• Remove the special wrench.
681BB379 KN
681BB380 KN
Checking length of lines
• Pull ends of lines firmly outward.
• If length is
more than 5 cm
: Cut to
length.
• If length is
less than 5 cm
: Lift spool
slightly so that it can be rotated. Pull out
the nylon lines – push spool in again and
turn it back and forth to engage.
Closing the mowing head
• Engage the tabs in the slots.
• Press the cover down and check that it is
firmly seated.
Obtaining Correct Length of
Nylon Lines with Automatic Feed
Mechanism
•
Always read
and observe the
instructions in your brushcutter
instruction manual.
• Start your brushcutter.
• Hold the mowing head horizontally over a
bare, flat surface.
• Run engine at full throttle until its speed
remains constant, i.e. steady engine
note. – Nylon lines are adjusted
automatically.
• Let go of the throttle trigger and wait for
the engine to return to idle speed. Nylon
lines will be adjusted again to their final
length.
You may hear a brief knocking sound during
this adjustment – a slight jerk will be felt.
• Repeat the above procedure a few times.
• Switch off the engine and wait for the
mowing head to come to a complete
stop.
Checking Length of Lines
• Pull the ends of the lines in the direction
of the blade on the deflector.
Correct line lengths:
- on models FS 160, 180, 220, 280, 290,
300, 310, 350, 400, 450, 480:
12 to 14 cm
.
- on models FS 260, 360, 410, 460, 490:
15 to 17 cm
.
The adjustment is OK if the line lengths are
within the above mentioned limits.
If lines extend right up to blade and have
been cut off several times (watch for pieces
of nylon line on ground):
• Go to “Changing Setting of Mowing
Head”.
STIHL SuperCut 40-2
0457 567 9900 D G13
G
www.stihl.com
©
AN
DRE
AS
ST
IH
L
AG
&
C
o.
KG
, 20
13
