EN
NO
33
SV
FI
DA
PL
0478 192 9810 A - EN
For this purpose, the following checks are
required before each start (visual
inspection):
– Wear and damage to tyres.
– Leaks in fuel carrying lines.
– Engine oil level (see engine instruction
manual).
– Fuel-tank level.
– General visual inspection of the
machine and mowing deck. Particularly
the protective covers must be inspected
for damage.
– Tightness of bolted connections.
Maintenance operations after each use:
– Cleaning the machine (mowing deck,
mowing deck discharge opening) and
any attachments.
– Observe the instructions on cleaning
the engine (see engine instruction
manual).
– Clean the gearbox by brushing off grass
residues and any other dirt.
Maintenance operations after the first
10 operating hours (initial operation):
– An inspection by your specialist dealer
is recommended.
STIHL recommends STIHL specialist
dealers.
Maintenance operations after every
25 operating hours:
– Check of blade fastening and blade
sharpness, observe blade wear limit.
Maintenance operations after every 50
operating hours:
– General lubrication.
– Checking the installation position of the
Maintenance operations after every 100
operating hours:
– Replace the mowing blades.
– Allow inspection to be carried out by a
specialist dealer.
STIHL recommends STIHL specialist
dealers.
14.2 Cleaning the machine
●
●
●
Remove the ignition key and keep it in a
safe place.
●
●
First, remove accumulated clipping
deposits in the mowing deck housing
using a stick.
●
Clean the underside of the mowing
deck with water and a brush.
●
When cleaning the upper side of the
mowing deck, ensure that the V-belt
does not get wet – never spray water
into the openings in the covers.
●
Remove grass residues from the
mowing deck, the engine compartment
and the gearbox. Clean the cooling ribs
of the engine and gearbox.
●
Clean the mowing blades with water
and a brush – under no circumstances
should you hit the mowing blades
(e.g. with a hammer) to loosen dirt.
14.3 Opening the engine hood
Note
During the inspection by the
specialist dealer, the braking
function is checked and, if
necessary, the brakes are serviced.
Furthermore, all required
maintenance operations on the
gearbox are carried out.
Avoid damage to the machine!
Never spray water (high-pressure
cleaner) onto engine components,
seals, electrical components
(battery, wiring harness, etc.) and
bearing points. This may result in
damage and expensive repairs.
Do not use aggressive cleaning
agents. These cleaners can
damage plastics and metals,
impairing the safe operation of your
STIHL machine. If you are unable
to remove the dirt with water using
a brush or a cloth, STIHL
recommends the use of a special
cleaner (e.g. STIHL special
cleaner).
Always remove the mowing deck
for cleaning and maintenance
operations.
Risk of injury!
Switch off the engine and allow it to
cool down for a few minutes before
opening the engine hood.
The engine should be warm to the
touch.
Summary of Contents for RT 4097 S
