manualshive.com logo in svg

Stihl FR 350, Instruction Manual

Share
Download
Stihl FR 350 Instruction Manual Download Page 12

11

FR 350, FR 450, FR 480

English

Symbols on Deflectors

An arrow on the deflector shows the 
correct direction of rotation of the cutting 
tools.

Use deflector in 
combination with 
mowing heads 
only. Do not use 
metal cutting tools.

Mowing Head with Nylon Line

Nylon line achieves a soft cut for edging 
and trimming around fence posts, trees, 
etc. – less risk of damaging tree bark.

To reduce the 

risk of injury

, 

never

 

use steel wire in place of the nylon 
cutting line.

STIHL PolyCut Cutting Head with 

Plastic Blades

The PolyCut is used for edging fields not  
bordered by posts, fences, trees or other 
obstacles.

Check wear limit marks!

If one of the marks on the PolyCut is 
worn through (arrow): To reduce the 

risk 

of injury

 from thrown parts, 

stop using 

the head immediately

. Install a new 

one.

It is important to follow the maintenance 
instructions for the PolyCut cutting head!

000BA015 KN

002BA177 KN

Summary of Contents for FR 350



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands