STIHL 020 T
57
11.
Special Servicing Tools and Aids
11.1
Special Servicing Tools
No.
1
2
3
4
5
6
7
8
9
10
11
12
16
17
18
13
14
15
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
Part Name
Locking strip for piston
Press sleeve
Assembly sleeve
Assembly hook
Assembly tube
Assembly drift
Clamping strap
Wooden assembly block
Carburetor and
crankcase tester
Vacuum pump
- Nipple
- Fuel line
Sealing plate
Test flange
Setting gauge
- Flange
- Pin
- Pan hd. screws
Stud puller M8
Installing tool 9
Puller
Service tool AS (set)
- Threaded sleeve
Screwdriver bit T27x125
Socket, 13 mm
Torque wrench
Torque wrench
Assembly tool
Installing tool
Assembly hook
Screwdriver T20x100
T-handle screwdriver
Q-SW 8x200
Crimping tool
Assembly stand
Screwdriver T27x150
Puller
- Jaws
Socket T20x125
Part No.
0000 893 5903
1129 893 2400
1129 893 4600
5910 890 2800
1117 890 0900
1114 893 4700
0000 893 2600
1108 893 4800
1106 850 2905
0000 850 3501
0000 855 9200
1110 141 8600
0000 855 8106
1128 850 4200
1111 890 6400
1123 850 4200
0000 963 1008
9043 319 8100
5910 893 0501
5910 890 2209
1116 893 0800
5910 007 2205
5910 893 2407
0812 542 2104
5910 893 5608
5910 890 0301
5910 890 0302
5910 890 0311
5910 890 0312
1116 893 4800
0000 890 2201
5910 893 8800
5910 890 2301
5910 890 2420
5910 890 8210
5910 850 3100
5910 890 2302
0000 890 4400
0000 890 3700
0812 542 2041
Application
Blocking the crankshaft
Installing oil seal and roller
bearing in crankcase
Protecting oil seal at
ignition side
Detaching springs from
clutch shoes
Attaching the brake spring
Fitting piston pin
Compressing piston rings
Fitting piston
Testing carburetor and crankcase
for leaks
Testing crankcase for leaks
Sealing exhaust port for
leakage test
For leakage test
Setting air gap between ignition
module and flywheel
Removing bar mounting stud
Fitting hookless snap rings
in piston
Removing flywheel
Separating crankcase halves
For IS screws (5 mm)
Crankshaft nut (ign. end) and clutch
Screw assemblies (0.5 to 18 Nm)
Screw assemblies (6 to 80 Nm)
Installing rewind spring
Flaring rope guide bush
Removing pickup body
For all IS-P screws (4 mm)
Carburetor nuts
Attaching connectors to
electrical wires
Holding saw for repairs
For all IS screws (5 mm)
Removing oil seals
Tightening IS-P screws (4 mm)
Rem.
1)
2)
1)
2)
Remarks:
1) Plastoform and DG screws must always be tightened with torque wrench.
2) Wrench has optical/acoustic signal.
