Stiga PARK PRO 16 Instructions For Use Manual Download Page 11

67

ENGLISH

EN

3. Release the control lever (1:S) to lock the seat.
The seat is equipped with a safety switch that is 

connected to the machine’s safety system. This 

means that certain dangerous activities are not pos-

sible when there is nobody sitting on the seat. Also 

see 4.3.2.

2.4.18 Engine casing (7:U)

In order to access the fuel cock, battery 

and engine, the machine has an engine 

casing that can be opened. The engine cas-

ing is locked with a rubber strap.

The engine casing is opened as follows:
1. Undo the rubber strap (7:V) at the front edge of 

the casing.

2. Carefully lift the engine casing back.
Close in the reverse order.

The machine may not be operated un-

less the engine casing is closed and 

locked. Risk of burns and crushing in-

juries.

2.4.19Quick-release mounting (34:H)

The quick-release mountings allow the 

deck to be moved easily between the two 

positions:
•Normal position with fully tensioned 

belt.

• 4 cm behind the normal position with slackened 

belt.

As the belt idler is released from the belt, the 

quick-release mountings simplify belt and deck re-

placement, and also make shifting to the washing 

position and service positions easier.

Releasing the belt tension:

1. Remove the locking pins (34:G) from both 

sides.

2. Press down the rear section of the quick-release 

mountings (34:F) with the lug.

3. Carry out necessary corrective action, e.g. set-

ting the deck to the washing position.

Tensioning the belt:

First tension one side and then the other according 

to the instructions below.

Use protective gloves when handling the 

lever. Risk of crushing injuries.

1. Firmly grasp the lever (35:J) in front of the cen-

tre of the shaft and carefully turn 180° forwards.

2. Install the locking pin (34:G).
3. Carry out the above on the other side.

3 AREAS OF USE

The machine may only be used for the following 

tasks using the genuine STIGA accessories stated.

The maximum vertical load on the towing hitch 

must not exceed 100 N.
The maximum over-run load on the towing hitch 

from towed accessories must not exceed 500 N.
NOTE! Before using a trailer – contact your insur-

ance company.
NOTE! This machine is not intended to be driven 

on public roads.

4 STARTING AND OPERATION

The machine may not be operated un-

less the engine casing is closed and 

locked. Risk of burns and crushing in-

juries.

4.1 Filling with petrol

Always use lead-free petrol. You must never use 2-

stroke petrol mixed with oil.
The tank holds 14 litres. The level can easily be 

read through the transparent tank.
NOTE! Ordinary lead-free petrol is a perishable 

and must not be stored for more than 30 days.

Work

Accessories, STIGA genuine

Mowing

Using mowing decks:
95C, 95C El, 105C, 105C El, 

121 M, 121 M El, 110 Combi 

Pro, 110 Combi Pro El, 125 

Combi Pro, 125 Combi Pro El 

and with flail mower.

Sweeping

Using brush unit or collector 

brush unit. The use of a dust 

guard is recommended with the 

first option.

Snow clearance

Using snow blade or snow 

thrower Snow chains are recom-

mended.

Grass clipping and 

leaf collection

Using towed collector 30" or 

42".

Grass and leaf 

transport

Using dump cart Standard, Maxi 

or Combi.

Sand spreading

Using sand spreader. Can also 

be used for spreading salt. Snow 

chains are recommended.

Weeding on gravel 

paths

Using front-mounted hoe.

Lawn edge trim-

ming

Using edge trimmer.

Moss scarification Using moss scarifier.

Summary of Contents for PARK PRO 16




















Reviews: