STIEBEL ELTRON DEL 13 Plus AU Operation And Installation Download Page 7

iNSTALLATiON 

 

Safety

EN

GL

ISH

www.stiebel-eltron.com 

DEL Plus AU | 

7

 

Note

After a power failure 

Programming unit displays and selected settings are re-

tained following a power failure.

If you cannot remedy the fault, contact your qualified contractor. 

To facilitate and speed up your request, provide the number from 

the type plate (000000-0000-000000).

Nr. 000000-0000-00000

Nr. 000000-0000-00000

D

00000

53

31

2

iNSTALLATiON

7.  Safety

Only a qualified contractor should carry out installation, commis-

sioning, maintenance and repair of the appliance.

7.1  General safety instructions

We guarantee trouble-free function and operational reliability only 

if original accessories and spare parts intended for the appliance 

are used.

!

 

Material losses

Observe the maximum inlet temperature. Higher tem-

peratures may damage the appliance.  You can limit 

the maximum inlet temperature by installing a central 

thermostatic valve (see chapter "Appliance description / 

Accessories").

 

CAUTION Burns

If the water supplied to the appliance is preheated, 

please note the following points:

 

-

The internally adjustable anti-scalding protection 

and the temperature limit that is adjustable by the 

user may be exceeded.

 

-

The dynamic anti-scalding protection between the 

appliance and the wireless remote control may not 

be effective.

f

f

In both cases, limit the temperature with an up-

stream central thermostatic valve.

 

WARNING Electrocution

This appliance contains capacitors which are discharged 

when disconnected from the power supply. The capacitor 

discharge voltage may briefly reach > 60 V DC.

7.2  Instructions, standards and regulations

 

Note

Observe all applicable national and regional regulations 

and instructions.

 

- The IP 25 (hoseproof) rating can only be ensured with a cor-

rectly fitted cable grommet.

 

- The specific electrical resistivity of the water must not fall 

below that stated on the type plate. In a linked water net-

work, factor in the lowest electrical resistivity of the water. 

Your water supply utility will advise you of the specific elec-

trical water resistivity or conductivity.

Summary of Contents for DEL 13 Plus AU





















Reviews: