background image

114

option

A

A

A

28

/

29/30

For 6 Cylinder (Series SE)

There are 2 sacrificial zinc anodes in the raw water cooling system 

normally, If an exhaust high riser is used, there is one extra installed 

see fig. 28, 29 and 30.

Remove and inspect anodes for galvanic erosion according to the 

maintenance schedule.

Replace anode when material loss is 50 - 75 %.

Anti-Corrosion Anodes

If additional electronic equipment is installed, each should have 

an individual anode or grounding device and all grounding devices 

must be interconnected. Follow recommendations of manufacturers 

of equipment.

NOTE:  

Inspect anodes every 30 days, or more 

frequently if used in extremely salty water. 

Anode is to be replaced according to the 

maintenance schedule.

Boats that connect to an AC power source (shore power) require 

protection against increased potential of galvanic and “spray cur-

rent” corrosion. For protection, a galvanic isolator can be installed 

in series with the grounding (green) wire in the shore power cable 

between the boat and the shore power outlet on the dock. The isola-

tor blocks direct current (DC) flow, but permits the passage of alter-

nating current (AC) thus providing a path for ground fault currents.

NOTE:  

If a boat is connected to an AC power source 

(shore power), and it is not equipped with 

a galvanic isolator, the zinc anti-corrosion 

anodes may be unable to handle the added 

corrosion potential.

Summary of Contents for MO114K33







































































































































Reviews: