Stewart MacDonald 5297 Assembly Instruction Manual Download Page 5 | Manualshive

Page: 5 / 42

Stewart MacDonald 5297 Assembly Instruction Manual Download Page 5

stewmac.com

1 Bent sides, rosewood or

mahogany, depending on

    your kit (2)
  2  Kerfed lining (8)
  3 Fretboard
  4  Mahogany neck, dovetail

    or bolt-on
  5  Rosewood peghead overlay
  6  Maple bridge plate stock
  7  Neck block, dovetail or

   bolt-on
8 Tailblock
  9  Thick binding, black or white
10  Thin binding, white and black
11   Sitka spruce soundboard
12  Bridge
13  Back, rosewood or mahogany
14  Building an Acoustic Guitar Kit
   DVD

Kit parts list

15 Blueprint, body and bracing

   patterns
16  Heel cap and end trim
17  Herringbone rosette (3 pieces)
18  Top brace set, plus 2 unshaped

   X-braces
19  Fretwire (3)
20  Bone saddle blank
21  Bone nut blank
22  Diamond shaped inlays,
    small (4), and large (3)
23  White side dot material
24  Back brace set (9 pieces)
25  Endpin
26  Bridge pins (6)
27  Hot Rod truss rod
28  Reinforcement strips (3)
29  Shim stock (not in bolt-on kit)

Not pictured: this assembly

instructions book, cardboard

body mold (2), scrap wood,

and large rubber band

1

2

3

4

5

6

7

8

9

10

11

12

13

16

14

15

17

18

19

20

21

22

23

24

25

26

27

28

29

3

«
...
3
4
5
6
7
...
»

Summary of Contents for 5297











































Reviews:

No comments