background image

SETUP AND MOVING 

5

© 2015 KISS Catalog, Ltd. 

Under License to Epic Rights.

KISS PREMIUM EDITION MANUAL #500-55H3-01

FIRST-TIME SETUP CONTINUED

30.  If pinballs were already installed into the lower ball 

trough, remove them before lifting the playfield.

31.  Grasp the lower arch between the flippers, and firmly 

but gently pull directly up to raise the playfield 8-12 

inches. 

32.  While holding the playfield up, pull the playfield toward 

you until the two playfield supports are over the front 

edge of the cabinet. 

33.  Rest the playfield on the front edge of the cabinet. 

34.  Raise the playfield and rest it against the backbox.

35.  Visually inspect all cabinet cables and connector termi-

nations; ensure no wires or cables are pinched and that 

cable harnesses are not pulled tight.

36.  Locate the plumb bob in the parts bag in the cash box

37.  Slide plumb bob onto the hanger wire. Note: the vertical 

position of the plumb bob affects tilt sensitivity - higher 

makes the game more sensitive to tilting.

38.  Tighten the Thumb Screw finger-tight.

39.  Install the correct number of pinballs. Refer to the decal 

on the lock down assembly for the correct number of 

pinballs.

LOCATING, LEVELING, AND FINAL SETUP

1.  Select a location that is indoors, out of direct sunlight, 

and climate controlled. Excessive moisture/humidity 

can cause long-term damage to your game. 

2.  Adjust the front or rear levelers as necessary to position 

the playfield level bubble, located on the front right of 

the playfield next to the shooter lane, to float between 

the two (2) black lines. This will place the playfield at 

the recommended 6.5° pitch. Playfield angles greater 

than 6.5° can be achieved by turning out the rear leg 

leveler(s) for increased difficulty and faster gameplay. 

3.  Use a pinball to roll down the center of the playfield for 

side-to-side leveling, or use an external bubble level, 

digital level, or smartphone level app. 

4.  Plug into a grounded outlet and check for proper oper-

ation through DIAGNOSTICS.

5.  Check the coin door: With the door closed, insert coins 

to verify proper operation.

6.  Play game: Check for satisfactory operation and adjust 

game volume (push the Red Buttons inside the Coin 

Door).

7.  If desired, perform any game diagnostics, game adjust-

ments, and pricing settings at this time. 

To Purchase This Game, Visit BMI Gaming  |  www.bmigaming.com  |  Or Contact International Sales at + 561-391-7200 (USA) 

Summary of Contents for KISS PREMIUM





















































Reviews: