background image

INSTALLATION INSTRUCTIONS & PARTS LIST

STERLING GAS FIRED PROPELLER UNIT HEATERS

 (S) IIPLM-20

J30-05367

Model No.

Serial No.

FOR YOUR  SAFETY

The use and storage of gasoline or other ß ammable vapors and liquids in open containers in 

the vicinity of this appliance is hazardous.

FOR YOUR  SAFETY

If you smell gas:

1. Open windows.

2. DonÕt touch electrical switches.

3. Extinguish any open ß ame.

4. Immediately call your gas supplier.

ATTENTION: READ THIS MANUAL AND ALL LABELS ATTACHED TO THE UNIT CAREFULLY BEFORE 

ATTEMPTING TO INSTALL, OPERATE OR SERVICE THESE UNITS! CHECK UNIT DATA PLATE FOR TYPE OF 

GAS AND ELECTRICAL SPECIFICATIONS AND MAKE CERTAIN THAT THESE AGREE WITH THOSE AT POINT OF 

INSTALLATION. RECORD THE UNIT MODEL AND SERIAL No.(s) IN THE SPACE PROVIDED. RETAIN FOR FUTURE 

REFERENCE.

INSTALLER'S RESPONSIBILITY

Installer Please Note:

 This equipment has been test fired and inspected. It has been 

shipped free from defects from our factory. However, during shipment and installation, 

problems such as loose wires, leaks or loose fasteners may occur. 

It is the installer's 

responsibility to inspect and correct any problems that may be found.

 Install, operate and maintain unit in accordance with manufacturer's 

instructions to avoid exposure to fuel substances or substances from incomplete 
combustion which can cause death or serious illness. The state of California 
has determined that these substances may cause cancer, birth defects, or other 
reproductive harm.

 Improper installation, adjustment, alteration, service or maintenance 

can cause property damage, injury or death. Read the installation, operating and 
maintenance instructions thoroughly before installing or servicing this equipment.  

APPROVED FOR USE IN CALIFORNIA WHEN EQUIPPED WITH SPARK IGNITION.

RECEIVING INSTRUCTIONS

Inspect shipment immediately when 

received to determine if any damage 

has  occurred  to  the  unit  during 

shipment.  After  the  unit  has  been 

uncrated,  check  for  any  visible 

damage to the unit. If any damage 

is found, the consignee should sign 

the  bill  of  lading  indicating  such 

damage and immediately file claim 

for damage with the transportation 

company.

260 NORTH ELM ST., WESTFIELD, MA 01085

TEL: (413) 564-5540     FAX: (413) 562-5311

www.sterlinghvac.com

MODELS: QVF (30, 45, 60, 75, 100, 125, 150, 

175, 200, 225, 250, 300, 350, 400) (S,M)

10/07

HVAC PRODUCTS

Summary of Contents for M)

























Reviews: