Steris P920011-649 Operator'S Manual Download Page 92

Page: 92 / 168

4-47

Processing Instructions

Operator Manual

920011-649

4.13 Responding to a

Fault

Fault messages warn operator if the processor is experiencing an

abnormal condition. Fault conditions can be caused by failure of

utility supplies or by processor components.
Refer to

for a detailed listing of fault

alarms.

NOTE:

Some fault conditions can be solved by the operator.

4.13.1 Faults

When a malfunction or fault occurs before the cycle is successfully

completed:
1. An alarm sounds and display shows:

alternating with:

and printer records:

=========================
HH:MM:SS XM

MM-DD-YY

=========================
= FAULT XX

=========================

2. Press

ALARM REPLY

touch pad to acknowledge alarm. This

will record time at which operator acknowledged alarm. Printer

records:

=======================
HH:MM:SS XM

MM-DD-YY

=======================
ALARM ACKNOWLEDGED
=======================

FAULT

alarm requires no further action (for example, refer to

), or if the operator

has been able to solve the fault condition using

ECTION

ROUBLESHOOTING

, display shows:

3. Press

START

touch pad to resume cycle operation. Display

shows:

FAULT XX

CYCLE DELAYED

SEE FAULT CHART

CYCLE DELAYED

START TO RESUME

STOP TO CANCEL

OPERATING

MMM MIN

WARNING

–

INEFFECTIVE

PROCESS HAZARD: Endoscopes
and

accessories

are

not

adequately processed, rinsed
and

air

purged

when

processing cycle is aborted.
REPROCESS LOAD.

Summary of Contents for P920011-649









































































































































































Search results

Summary of Contents for P920011-649

Reviews:

Related manuals for P920011-649

Brands by name

Popular brands

Steris P920011-649, Operator'S Manual

Search results

Summary of Contents for P920011-649

Reviews:

Related manuals for P920011-649

Brands by name

Popular brands